Felling in wind: the stop-work and wind-check wording in six codes
OSHA, WorkSafe New Zealand and SafeWork NSW carry wording about stopping work in strong winds. WorkSafeBC, HSE and Michigan name wind or weather as a condition to check. No code prints a wind speed.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
The text below describes what the named codes and training bodies publish. It is not training and does not teach the work. Six official documents mention wind in connection with felling. Three carry words about stopping or suspending work. Three name wind as a condition to check. None of the six prints a wind speed or other numeric cutoff.
Wind and stop wording by code
| Code and section | Wording |
|---|---|
| OSHA, 29 CFR 1910.266(d)(5) and (h)(2)(ii), logging | Wind: Strong winds which may affect the fall of a tree are listed among the environmental conditions, with electrical storms, heavy rain or snow, extreme cold, dense fog, fires, mudslides and darkness. Before each tree is felled, the feller evaluates conditions such as snow and ice accumulation, the wind, the lean of the tree, dead limbs and the location of other trees. Stop: All work terminates and each employee moves to a place of safety when such conditions, listed as "such as but not limited to", create a hazard for the employee |
| WorkSafeBC, OHS Regulation section 26.7.2, forestry operations | Wind: Wind is not named. Weather conditions are covered together Stop: When weather conditions create a hazard for a worker, additional precautions must be taken as necessary for the safe conduct of the work. No stop wording |
| SafeWork NSW, Tree works code of practice, March 2026, section 3.3 and chapter 9 | Wind: Strong winds can damage or weaken trees, affect communication, destabilize plant or workers near the tree, and cause branches to sway or fall unexpectedly. The visual assessment before felling considers wind loading and current weather conditions Stop: During hazardous weather conditions, such as strong winds, lightning activity, extreme heat or torrential rain, work should stop and be rescheduled |
| HSE, Chainsaws at work, INDG317 (rev2, January 2013) | Wind: When felling, assess what could affect the direction of fall, such as wind conditions and whether the tree is leaning, has uneven growth or has branches that could foul other trees. Leaning trees and wind-blown trees also need special skills Stop: No stop wording |
| Michigan, Mich. Admin. Code R 408.15151(2), logging, felling | Wind: Before a cut starts, the feller checks for other employees, dead limbs, lean, wind condition, other trees and hazards, and snow or ice. The feller then plans and clears a path of retreat Stop: No stop wording. The immediate supervisor is consulted when unfamiliar or unusually hazardous conditions need approval before cutting starts (subrule 5) |
| WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, sections 2.2 and 3.4.1 | Wind: The planning list for felling includes wind force and direction, and other climatic factors. Section 3.4.7 calls windthrown trees an added hazard Stop: Where any operation becomes dangerous because of high winds, wet weather, poor visibility or other adverse conditions, the employer or person in charge suspends operations while those conditions exist |
Where the wording is firm and where it is not
OSHA's logging standard and WorkSafe New Zealand use "shall": work terminates or is suspended. SafeWork NSW uses "should": work should stop and be rescheduled. The NSW code is an approved code of practice, and the New Zealand document is an Approved Code of Practice under the Health and Safety in Employment Act. The OSHA wording is in federal regulation.
WorkSafeBC treats weather as a hazard that calls for added precautions. Part 26 also carries a section 26.17, Weather conditions, marked repealed effective May 1, 2008. Section 26.7.2 holds the weather wording.
HSE and Michigan treat wind as one input to the felling plan, next to lean, dead limbs and snow. Michigan adds the retreat path to the same list. HSE's leaflet is guidance for employers and the self-employed on hand-held petrol chainsaws.
Wind on the page before the cut
In four of the six, wind appears in the same breath as the lean of the tree: OSHA, HSE, Michigan and the New Zealand planning list. SafeWork NSW lists wind loading next to the condition of the tree, its structural integrity and its branches. For felling distances from the same regulators, see the guide to felling distances and danger zones. The cuts that follow that check carry their own names in the codes: see the guide to notch, hinge and back cut names.
Sources
- eCFR, 29 CFR 1910.266 Logging operations, current text, read October 21, 2026
- WorkSafeBC, OHS Regulation Part 26 Forestry Operations, section 26.7.2, read October 21, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 21, 2026
- HSE, Chainsaws at work, INDG317 (rev2), published January 2013, read October 21, 2026
- Cornell LII, Michigan Administrative Code R 408.15151 Felling, read October 21, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 21, 2026