Firewood processors by type and power source: what EU regulators, BSI and OSHA describe
EU market surveillance authorities describe firewood processors by feed, mounting and power source: engine, electric, or tractor power take off. BSI covers the saw and the splitter in separate standards.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The main document is the Machinery ADCO paper WG-2015.27, endorsed in October 2015 under Directive 2006/42/EC. The paper is not legally binding, and only the Directive as written into national law binds. BSI scope pages for EN 1870-6 and EN 609-1 and the OSHA machine guarding rule add the rest. No skid-steer driven processor is described in any of them.
Types in the Machinery ADCO paper
The paper reports a survey of processors on the European market in 2012 to 2014. It describes the usual machine as a sequential cutting and splitting machine. A feed zone leads to a chainsaw or circular saw, the cut logs usually drop into a splitter, and the pieces leave on a discharge conveyor that is often inclined. Most machines are meant for use at work.
| Basis | Types named |
|---|---|
| Power source | An on-board combustion engine, single or three phase electric power, or an agricultural tractor through the power take off shaft or the hydraulic system |
| Mounting | Static machines set on a base, towed machines, machines with demountable wheels, and short machines carried sideways on a tractor three point linkage |
| Feed | Mechanically fed, usually by a horizontal conveyor, and manually fed. A subset is lifted and thrust in by hand into a rotating blade with a spike that cuts and splits in one operation |
| Cutting means | Chainsaw or circular saw, with a hydraulic ram pushing against a fixed splitting plate |
Guard lengths and stops in the paper
The paper sets out what the authorities regard as the state of the art. Its figures are recommendations:
- Machines on electric power should have one or more emergency stops that stop all moving parts. Engine-driven machines may stop by shutting down the engine, and power take off machines should stop quickly from the operator's position.
- Circular saw cutting means should stop within 10 seconds, or the guards should stay locked until the blade is at rest.
- Mechanically fed machines should have in-feed guards at least 850 mm long. With a hinged pressure plate that closely fits the guard the length may be shorter, but probably not under 650 mm.
- Discharge guarding should give an 850 mm safety distance to the front cutting edge of the splitting blade. Permanently fixed or interlocked guarding should in no case give less than 550 mm.
- Manually fed machines should have in-feed guards at least 850 mm long. Where wood is lifted and thrust in, the paper gives fixed guards of 1100 to 1200 mm.
- Two-hand controls are not a substitute for guarding, because other people are often near these machines and throughput is higher than for simple splitters.
The paper recommends an absolute minimum ingress protection rating of IP44 for electrical parts on machines used outdoors. Where makers stated a rating, IP44 was the minimum, several stated IP55, and one stated IP56. It was written in part to inform CEN on a proposed new part of EN 609 for these machines.
BSI standards for the parts
BS EN 1870-6:2017 covers circular sawing machines for firewood with manual loading or unloading and a hand-operated carriage. BSI lists it as current and designated under the Machinery Directive. It does not apply to combined machines that add a log splitting unit or a circular saw bench unit, to machines with a tilting blade, or to machines where the saw unit moves to cut. A note in the scope says a draft was under consideration to cover combined firewood processors.
BS EN 609-1:2017 covers horizontal and vertical wedge splitters for firewood, whatever the power source. BSI lists four machine categories: horizontal and vertical, each for long logs or short logs. The standard does not apply to machines designed for cutting to length and splitting for firewood. Hauling winches fitted to wedge splitters are covered by new tests in the 2017 edition.
OSHA machine guarding
OSHA 29 CFR 1910.212 applies to all machines in United States workplaces and names no firewood processor. It requires one or more guarding methods against hazards from the point of operation, ingoing nip points, rotating parts, flying chips and sparks. Barrier guards, two-hand tripping devices and electronic safety devices are examples. Power saws are on its list of machines that usually need point of operation guarding. Guards are to be affixed to the machine where possible, and machines made for a fixed location are to be anchored against walking or moving.
Sources
- Machinery ADCO, Recommendations for improving the safety of Firewood Processors, open annex WG-2015.27, October 2015, read October 16, 2026
- BSI Knowledge, BS EN 1870-6:2017 circular sawing machines for fire wood, scope, read October 16, 2026
- BSI Knowledge, BS EN 609-1:2017 safety of log splitters, wedge splitters, read October 16, 2026
- eCFR, 29 CFR 1910.212 General requirements for all machines, current text, read October 16, 2026