Skid steer loaders: OSHA bulletin, federal standards and CDC fatality findings
OSHA's 2009 bulletin says OSHA has no standard requiring skid-steer seatbelts or interlocks, and 29 CFR 1926.602 reserves rules for rubber-tired skid-steer equipment. A CDC report describes the fatalities.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. It is not training and does not teach the work.
Federal standards and skid-steer loaders
Section 1926.602(a)(1) lists the earthmoving equipment its rules cover: scrapers, loaders, crawler or wheel tractors, bulldozers, off-highway trucks, graders, and agricultural and industrial tractors. It then reserves the rules for compactors and rubber-tired "skid-steer" equipment, pending standards then in development. Seat belts under (a)(2) are required on the equipment the section covers. They need not be provided for stand-up equipment or for equipment without a rollover protective structure (ROPS) or adequate canopy protection. Paragraph (a)(6) sends the reader to subpart W for ROPS.
Section 1910.178 is the powered industrial truck standard. By its own terms it does not apply to farm vehicles or to vehicles intended primarily for earth moving or over-the-road hauling. Its paragraph (l) is the operator training rule for the trucks it does cover.
| Section | Reach |
|---|---|
| 29 CFR 1926.602 | Earthmoving equipment in construction. Skid-steer rules reserved |
| 29 CFR 1910.178 | Powered industrial trucks. Earth-moving vehicles excluded |
| 29 CFR 1910.147 | Control of hazardous energy. May apply to skid-steers in situations covered by Part 1910, as the bulletin notes |
Training under 1910.178(l) is a program of formal instruction, practical training and an evaluation of the operator's performance in the workplace, run by people with the knowledge, training and experience to train and evaluate. Trainees may operate only under direct supervision and where it does not endanger them or others.
OSHA Safety and Health Information Bulletin 01-12-2009
The bulletin, Hazards Associated with Operating Skid-Steer Loaders with Bypassed and/or Improperly Maintained Safety Devices, states that it is not a standard and creates no new legal obligations. Its scope is the seatbelts and interlock systems on skid-steer loaders intended mainly for earth moving, which fall outside 1910.178. It names the common safety features: the seatbelt, a falling object protective structure (FOPS), a ROPS and a control interlock system.
OSHA's incident review covered 1997 to 2007. The Integrated Management Information System recorded 100 accidents involving skid-steer loaders. Deliberate bypassing of safety features such as seatbelts and interlocks was the direct cause of 20% of them, and all but one of those ended in a fatality. The bulletin describes three cases. In each the employer received a serious citation under the General Duty Clause. Causes it names include a disabled interlock, a bypassed safety bar and improper training, and in one case the on-the-job training left out the operator's manual.
OSHA states that it has no standard requiring control interlocks or seatbelts on skid-steer loaders. Its position is that an employee who leaves the proper position on an energised machine creates crushed-by and caught-in hazards, and that going without a seatbelt adds rollover risk. For construction work the bulletin points to 29 CFR 1926.20(b)(2), frequent and regular inspections by competent persons, and 1926.21(b)(2), instruction in recognising and avoiding unsafe conditions.
The bulletin's list of safety practices includes reading the operator's manual, following the manufacturer's instructions, keeping safety systems unmodified and in working order, and using an approved lift arm support device for work with the arms raised. It also lists training on inspection, use, maintenance and repair according to the manufacturer, and training supervisors to spot bypassed or disabled systems.
CDC MMWR: skid-steer fatalities, 1992 to 1995
The CDC report, Skid-Steer Loader-Related Fatalities in the Workplace, United States, 1992-1995, draws on three data sets.
- The NIOSH state FACE program received 22 reports of fatalities from eight states. The victims were aged 21 to 68, mean 40. Thirteen worked in agriculture, four in construction and two in services.
- The National Traumatic Occupational Fatalities surveillance system identified 25 deaths in 1980 to 1992 in which the worker was pinned by the bucket or lift arms. Fifteen, or 60%, were in 1988 to 1992.
- The Census of Fatal Occupational Injuries identified 20 such incidents in 1992 to 1994.
In 10 of the 22 FACE cases, the worker had been working or standing under a raised bucket. In five the worker had leaned out of the operator's compartment into the path of ascending or descending lift arms. The report says ROPS with side screens and safety belts give additional protection, and that interlock control systems can be bypassed and rendered inoperative.
Sources
- OSHA, Safety and Health Information Bulletin 01-12-2009, Hazards Associated with Operating Skid-Steer Loaders with Bypassed and/or Improperly Maintained Safety Devices, read October 16, 2026
- Cornell Legal Information Institute, 29 CFR 1926.602 Material handling equipment, read October 16, 2026
- Cornell Legal Information Institute, 29 CFR 1910.178 Powered industrial trucks, read October 16, 2026
- CDC, MMWR, Skid-Steer Loader-Related Fatalities in the Workplace, United States, 1992-1995, read October 16, 2026