ArbNation Join free

FISA 307 felling of large trees: what the guide covers

FISA 307 is the Forest Industry Safety Accord leaflet on felling and crown breakdown of large trees. It builds on FISA 302 and was once HSE guidance AFAG307.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work.

Scope of the leaflet

The Forest Industry Safety Accord (FISA) lists FISA 307 as "Chainsaw felling of large trees". Its scope covers the felling and crown breakdown of large trees, in plantations or as single large trees. It leaves out exceptional situations where the risk assessment shows that advanced or alternative felling techniques are needed. For those, FISA points to specialist advice and agreed safe methods of working.

The leaflet's own text says it is based on guidance that the Health and Safety Executive (HSE) published as AFAG307, "Chainsaw felling of large trees", withdrawn in 2013. The FISA PDF is marked "Reprinted 03/13". The Health and Safety Authority in Ireland lists the same leaflet as IFSG 307 in its forestry series, beside IFSG 301, 302, 303, 304 and 306.

Place in the FISA series

FISA 307 says the basic felling principles of FISA 302 must be read and applied together with it. The reason it gives is that the crown spread, depth, branching habit, size and surroundings of large trees create risks that need knowledge and techniques beyond basic felling, snedding and cross-cutting.

The leaflet also points to FISA 301 for protective equipment, the saw, fuelling and starting. It says operators need appropriate training in the machine and the tasks, and names the HSE leaflet INDG317 Chainsaws at work. Its further reading list names FISA 301, 302, 303, 304, 306, 310, 802 and 804, plus four HSE leaflets: INDG214, INDG294, INDG317 and INDG363. The leaflet carries a checklist block for a name, a checker and a date.

Like other FISA guides, it describes itself as evidence of good practice for a specific forestry task. Any departure should follow a full risk assessment by competent persons.

Sections of the leaflet

FISA 307, reprinted March 2013: sections and numbered points
SectionPointsTopics named in the leaflet
Tools required1A sledgehammer, wedges and an appropriately rated winch.
Felling2 to 5Distance from other people, the risk zone for crown wood, branch wood used as a cushion, and felling cuts in proportion to the tree.
Crown breakdown6 to 16Rolling and springback, tree stability, escape route, bystander distance, tension in branches, and the order of branch removal.

Felling, points 2 to 5

Point 2 sets a distance of twice the height of the tree between the feller and any other person, and never directly below on steep slopes. Point 3 notes that wood from the crown can travel a considerable distance when the tree hits the ground, so a risk zone has to be established.

Point 4 covers branch wood used to cushion the fall. The leaflet limits it to light material that is as long as possible. Point 5 sets the felling cuts in proportion to the tree's diameter, size and species and to the potential for decay.

Crown breakdown, points 6 to 16

The leaflet says crown breakdown can be very dangerous. The operator must always be prepared for the tree rolling or for springback when cutting branches. A properly anchored winch is named as a way to hold the tree stable during the work.

The leaflet also covers these points:

  • an escape route that stays clear and available at all times (point 8)
  • a risk zone that keeps bystanders at a safe distance until all parts of the tree are stable (point 9)
  • no work underneath any part of the felled tree (point 10)
  • continual assessment of tension in the branches, above all those supporting the main stem (point 11)

Points 12 to 16 set the order of branch removal. Smaller branch wood comes off to shoulder height first, with the main supporting branches and the stem retained. Heavy branches are shortened gradually where possible, not cut off at the stem. Branches above shoulder height are brought down by rolling the trunk under winch control. Delimbing flush to the trunk comes last, once all branches are off and the timber lies stable.

HSE on chainsaw felling

The HSE page on working with chainsaws lists key lessons from felling injuries and fatalities. It names the initial site survey, risk assessment and emergency planning, work planning, felling cuts, felling aids, control lines, escape routes and staff competency.

On cuts, HSE says control of the fell comes from an appropriate combination of the directional or sink cut, the hinge and the main felling or back cut. The cuts must suit the tree size and form and be consistently accurate. On escape routes, HSE adds that accidents often happen when unforeseen or remote risks materialise, and that the tree may fall toward the intended route.

On competency, HSE warns that people holding only CS30 and CS31 with little extra experience can quickly meet situations beyond their skills. Larger and awkward fells, and the unique hazards of garden arboriculture, are its examples.

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0.

Sources