Forestry machines: feller bunchers, harvesters, forwarders and skidders and the standards that cover them
ISO 11850 sets general safety requirements for self-propelled forestry machines, from feller bunchers to harvesters. OSHA's logging rule names skidders and feller bunchers and requires protective structures on them.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. Three texts define the machines: the international standard ISO 11850:2011, the roll-over protection standard ISO 8082-1:2009, and the US logging rule at 29 CFR 1910.266.
ISO 11850:2011, general safety requirements
ISO 11850:2011 is titled Machinery for forestry, General safety requirements. ISO committee TC 23/SC 15 owns it. It was published on November 15, 2011 and runs 18 pages in English. It replaced the 2003 edition, which is withdrawn.
The scope covers self-propelled forestry machines and machines configured as forestry machines. It deals with the significant hazards common to fellers, bunchers, delimbers, forwarders, log loaders, skidders, processors, harvesters, mulchers and multi-function versions of them, as defined in ISO 6814.
The scope also lists what it leaves out. It does not deal with hazards specific to one machine, such as those of a particular attachment, so the standard alone does not address every significant hazard for most of the machines it covers. Chain shot, chain breakage on the upper side of the bar, lifting operation, remote control operation, work lights and road safety are outside it. For vibration, the test setup and work cycles are not dealt with. For noise, the verification method is not addressed. Maintenance or repairs by professional service personnel are outside it too.
The standard has two amendments, Amd 1:2016 and Amd 2:2022. Its life-cycle record shows stage 90.92, standard to be revised, from December 20, 2024, and a committee draft, ISO/CD 11850, in development.
ISO 8082-1:2009, roll-over protective structures
AFNOR lists ISO 8082-1:2009 as current, published in July 2009, 16 pages. Its title is Self-propelled machinery for forestry, Laboratory tests and performance requirements for roll-over protective structures, Part 1: General machines.
The standard sets out a repeatable way to evaluate the force and deflection of a roll-over protective structure (ROPS) under static loading. It also sets performance requirements for a representative specimen. It applies to forwarders, skidders, feller bunchers, processors, harvesters and log loaders as defined in ISO 6814. It does not apply to machines with a rotating platform carrying a cab and boom. ISO 8082-2 addresses those.
OSHA's logging rule, 29 CFR 1910.266
OSHA defines a machine as a piece of stationary or mobile equipment with a self-contained powerplant, operated off-road and used to move material. The definition names tractors, skidders, front-end loaders, scrapers, graders, bulldozers, swing yarders, log stackers and log loaders. It also names mechanical felling devices, such as tree shears and feller bunchers. Aircraft are excluded.
Paragraph (f)(3) covers protective structures. Each tractor, skidder, swing yarder, log stacker, log loader and mechanical felling device placed into initial service after February 9, 1995 is to carry a falling object protective structure (FOPS), a ROPS, or both. Machines capable of 360 degree rotation are excepted.
For machines made after August 1, 1996, the rule ties ROPS to SAE J1040 (April 1988). It also calls for a cab fully enclosed with mesh material, with openings no greater than 2 inches at the least dimension, unless other material gives equivalent protection and visibility. It ties FOPS to SAE J231 (January 1981). Both protective structures must meet SAE J397 on the deflection limiting volume.
Other paragraphs set a cab entrance height of at least 52 inches (1.3 meters) from the cab floor and a second means of egress from each cab. Machines placed into initial service on or after September 8, 1995 also need secondary brakes.
Machine types by text
| Machine | ISO 11850 | ISO 8082-1 | OSHA rule |
|---|---|---|---|
| Feller buncher | Yes | Yes | Yes |
| Harvester | Yes | Yes | No |
| Forwarder | Yes | Yes | No |
| Skidder | Yes | Yes | Yes |
| Processor | Yes | Yes | No |
| Log loader | Yes | Yes | Yes |
| Delimber and mulcher | Yes | No | No |
For definitions of each type, see the guide to forwarders, skidders, harvesters and winches. OSHA's full logging text is on its own page.
Sources
- U.S. Department of Labor, OSHA, 29 CFR 1910.266 Logging operations, eCFR current text, read October 21, 2026
- ISO, ISO 11850:2011 Machinery for forestry, General safety requirements, catalogue record on the Albanian DPS standards page, read October 21, 2026
- AFNOR Editions, ISO 8082-1:2009 Self-propelled machinery for forestry, ROPS laboratory tests, Part 1, read October 21, 2026