ArbNation Join free

Friction hitches by type: where the Prusik, Blake's, Distel and Valdotain are named

One 2021 Italian test paper lists the common arborist friction hitches together. SafeWork NSW names the Prusik, NZQA unit 25402 names four hitches, and the UK and New Zealand codes name none.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

The facts here come from the named codes, units and papers. It is not training and does not teach the work. Hitch names and test results appear, tying steps and illustrations do not.

Where each hitch is named

HitchNamed in
PrusikBianchini and colleagues (Forests, 2021) call it a two-way friction hitch that can make movable anchor points on double and single ropes, and one of the most studied. SafeWork NSW code 4.7 covers Prusik loops, and its glossary defines one as a loop of rope smaller in diameter than the climbing rope, attached with a Prusik knot and used to attach the climber to the rope. AHCARB311 lists the English Prusik knot and the double fisherman's knot/Prusik loop.
Valdotain tresseBianchini and colleagues call it a one-way knot, among the most commonly used, widely used in double rope work because it is very soft and sensitive, and made with a cord smaller than the rope. NZQA 25402 lists Valdotain Tresse.
Schwabisch and DistelBoth appear in Bianchini and colleagues' list of the knots used most often, and in the range of NZQA 25402.
Tautline, Blake's hitch, Machard and KnutNamed only in Bianchini and colleagues' list of the knots used most often, which they say changes with the techniques and equipment.
KlemheistNZQA 25402 lists klemheist, and AHCARB311 lists the Klemheist friction knot.
Rolling hitchAHCARB311 lists it in the aerial rigging group.

The hitch as a class in the codes

The WorkSafe New Zealand code defines a friction hitch as usually made of synthetic fibre and rated to at least 22 kN, used to secure a climber to the climbing line and permit controlled ascent, descent and work positioning. Section 3.2.5 sets three tests: the hitch moves freely up and down the line, activates and holds on its own, and holds the climber's weight plus equipment. The code adds that friction hitches should be constructed or tied with a minimum cordage diameter of 70 percent of the climbing line, and asks climbers to weigh fibre type, construction and diameter together with other components.

The UK ICoP defines a friction hitch as the term for the knots and hitches that control ascent, descent or position on the rope and self lock when released. Its friction cord criteria are suitability for the intended use, made of material resistant to the abrasion and temperatures of work and rescue, and attached so that the hitch locks positively and reliably when advanced or during descent. SafeWork NSW lists compatibility with the rope, ground testing before first use in a tree and inspection for heat and abrasion damage.

Test papers

Bianchini and colleagues at the University of Tuscia ran 36 tensile tests of two semi-static ropes with the Prusik and the Valdotain tresse on 8 mm cords. They report a maximum load of 18.7 kN, a maximum slip of 9.6 cm and a maximum change in rope diameter of 3 mm. The Prusik gripped harder: maximum loads were 11.9 kN and 15.1 kN for the Prusik on the two ropes, against 9.3 kN and 8.6 kN for the tresse. Differences came mainly from the hitch, not the rope. The authors add that friction hitches made by an arborist do not carry a European certification and are not recognised as PPE.

A rope maker's 2015 R&D page tested hitch cords on five arbor climbing lines. Its static test was a modified ANSI Z359.3 slow pull that set the hitch at 0.98 kN, relaxed it, then ramped to 4.45 kN and measured slippage. Its drop test used a 100 kg mass and a fall factor of 0.3. The maker concluded that different hitches on different ropes give different results.

Credits: SafeWork NSW text is adapted from the Tree works code of practice (March 2026), copyright State of New South Wales (SafeWork NSW), licensed under Creative Commons Attribution 4.0; changes were made, because the text is summarised and reworded. WorkSafe New Zealand material is summarised from its Approved Code of Practice for Safety and Health in Arboriculture, with the source acknowledged. The Forests paper is open access under Creative Commons Attribution 4.0.

Sources