Friction savers and cambium savers: how the codes define each device and its kN figure
WorkSafe New Zealand treats a friction saver as a cambium saver, with a 22 kN minimum. SafeWork NSW pairs a friction saver with an anchor sling, and the UK code puts cambium savers among temporary anchor devices at 18 kN.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page draws on the named codes and training bodies. It is not training and does not teach the work.
Definitions and figures by code
| Code and term | Wording |
|---|---|
| WorkSafe New Zealand, cambium saver | A device used to protect the bark, cambium and climber's line from damage caused by friction. A cambium saver used in a climbing system shall meet a minimum breaking strength of 22 kN |
| WorkSafe New Zealand, friction saver | Defined as: see cambium saver |
| New Zealand Arboricultural Association guide, friction saver | A rated device installed at roping points, used to aid movement and lessen friction on a climbing system, and to limit damage to trees. It is also called a cambium saver |
| New Zealand Arboricultural Association guide, cambium saver | The same wording as WorkSafe New Zealand, with the 22 kN minimum |
| SafeWork NSW, friction saver or anchor sling | Named in section 4.3 as the means of reducing friction or the likelihood of the rope walking along a branch junction |
| Industry Code of Practice, cambium or pulley saver | Listed in clause 3.10.6.2 with tape slings as a typical temporary anchor device |
The New Zealand Arboricultural Association's glossary has a second line, friction saver, that sends the reader to the term friction device.
Temporary anchor devices in the ICoP
The Industry Code of Practice for Arboriculture, Edition 2, defines temporary anchor devices as components that provide an artificial, temporary anchor point, as opposed to the natural structure of the tree. Any equipment used must be manufactured to the standard for temporary anchors. Anchors must be configured so they cannot slip up or down the stem. The anchor must have a minimum breaking strength of at least 18 kN.
The figures differ by code. WorkSafe New Zealand sets 22 kN for a cambium saver, and the ICoP sets at least 18 kN for a temporary anchor device.
False crotch and slings
WorkSafe New Zealand defines a false crotch as a system used to support an arborist line other than a natural crotch. It shall incorporate rings or a pulley that protect the system and the line from damage or failure, and each component is rated to a minimum of 22 kN.
EVS lists EVS-EN 566:2017, Mountaineering equipment. Slings. Safety requirements and test methods, as valid from 4 April 2017. The scope covers slings used for mountaineering including climbing. The New Zealand guide lists EN 566 among its mountaineering and climbing equipment standards.
Types the codes do not define
None of the four code documents defines ring, ring-on-ring, adjustable or fixed-length friction savers as separate types. Each defines the device by what it does.
Slings used to rig loads have their own guide. The anchor side gets a longer reading in the guide to anchor slings and friction savers.
Sources
- WorkSafe New Zealand, Approved code of practice for safety and health in arboriculture, November 2012, read October 16, 2026
- New Zealand Arboricultural Association, Best practice guide: safety requirements for NZ arboricultural operations, Edition 3.1, 2022, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, section 4.3, read October 16, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, clause 3.10.6.2, read October 16, 2026
- EVS, EVS-EN 566:2017 catalogue entry, read October 16, 2026