ArbNation Join free

Harness, lanyard and restraint in aerial lifts: what OSHA, WorkSafe NZ and WorkSafe Victoria publish

OSHA 1910.67 calls for a personal fall arrest or travel restraint system attached to the boom or basket. WorkSafe NZ ranks travel restraint above fall arrest. WorkSafe Victoria names the designated anchor point, not the handrail.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

The facts on this page come from the named regulators and standards bodies. It is not training and does not teach the work. The sources are OSHA's general industry and construction aerial lift rules, WorkSafe New Zealand's Working at height guidelines and the WorkSafe Victoria industry standard for EWPs.

OSHA: attached to the boom or basket

Paragraph 1910.67(c)(2)(v) says a personal fall arrest or travel restraint system that meets the requirements in subpart I of part 1910 shall be worn and attached to the boom or basket when working from an aerial lift. The same list says belting off to an adjacent pole, structure or equipment while working from an aerial lift shall not be permitted. Employees shall always stand firmly on the floor of the basket and shall not sit or climb on the edge of the basket or use planks, ladders or other devices for a work position. Climbers shall not be worn while working from an aerial lift.

The construction rule has its own wording. Paragraph 1926.453(b)(2)(v) says a body belt shall be worn and a lanyard attached to the boom or basket. Its note says that since January 1, 1998, section 1926.502(d) does not accept body belts as part of a personal fall arrest system. A body belt in a tethering or restraint system is acceptable and is regulated under 1926.502(e).

RuleWording on the harness or lanyard
29 CFR 1910.67(c)(2)(v)Personal fall arrest or travel restraint system, worn and attached to the boom or basket
29 CFR 1926.453(b)(2)(v)Body belt worn and lanyard attached to the boom or basket, with the note on body belts above
29 CFR 1910.67(c)(2)(iii) and 1926.453(b)(2)(iii)Belting off to an adjacent pole, structure or equipment not permitted

WorkSafe New Zealand: boom MEWPs and the hierarchy

The WorkSafe New Zealand guidelines, Working at height in New Zealand (August 2026), treat fall protection as personal protective equipment and as the last resort. If a hazard cannot reasonably be eliminated, for example by working from the ground, or controlled with engineering measures such as scaffolding, fall-protection PPE comes last. Within PPE the guidelines prefer restraint over fall arrest.

The guidelines rank the systems this way: travel restraint with fixed-length lanyards first, restrained fall second, limited free-fall with work-positioning straps third, free-fall with inertia reels fourth, and the restraint technique of active re-anchoring fifth. Travel restraint is the preferred harness system because it keeps a worker from reaching the edge. Fall arrest should be considered only when travel restraint is not reasonably practicable, since it does not stop the fall from happening.

For mechanical access plant, the guidelines say an operator in a boom-style MEWP should wear a safety harness with an adjustable, energy-absorbing lanyard attached to the anchor point. The energy absorber connects on the harness side, not the anchor side. Unless a risk assessment identifies a specific fall risk, a harness is not required on a scissor lift, because the guardrails give the primary fall protection. Where a harness is required, it attaches only to a designated anchor point approved by the manufacturer.

WorkSafe Victoria: harness on the platform

The WorkSafe Victoria EWP industry standard (Edition 4, June 23, 2023) says a full body safety harness needs to be worn by every person on the platform of a boom-type EWP or a vertical mast EWP fitted with a jib. The harness is made for attachment to a lanyard assembly and includes a personal energy absorber. It is secured to the designated anchor point on the EWP, not the handrail.

The standard gives three risks the harness helps control. One is a fall from the platform if it strikes an object. Another is a fall if the levelling system fails and the platform tilts or inverts. The third is a person being catapulted out, for example over uneven ground or a terrain drop-off.

  • Fall arrest harness systems need to comply with the AS/NZS 1891 series.
  • Lanyard length should be as short as possible while still allowing freedom of movement, and the operator should be able to keep both feet on the platform floor.
  • For low-height tasks a site-specific assessment should look at whether fall clearance is inadequate, so a fall arrest system could deploy and the person still hit the ground.
  • If no safer alternative exists, a lanyard in a travel restraint configuration with an energy absorber, secured to the designated anchor points, may be used.
  • A harness is needed on a scissor-type EWP only if the maker advises it or the risk assessment indicates it.

The standard also notes an exception over water. A harness could drag a person under if the EWP tips into water, so a recorded site-specific risk assessment should decide whether a harness or another risk control measure is required.

Sources