History of felling: the ax, the crosscut saw and the chain saw
Crosscut saws ruled felling from the 1880s to the 1930s, and axes chopped out the sloping cut. Chain saws became reliable in the 1940s, and Joe Cox's chain, started in 1947, spread them through the woods.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
The text below describes what the named codes and training bodies publish. It is not training and does not teach the work.
The ax
The Forest Service ax manual, in its chapter A Brief History of the Ax, traces the tool from a stone used mostly for breaking to a hardened steel head. European explorers brought European-style axes to America, but the manual says those were not stout enough for the timber and the hard use. The common early styles were trade axes, the German ax, the Spanish ax and the Anglo-American ax, all with narrow cutting edges and no poll. A poll on the back and a more rectangular cutting edge set early American patterns apart.
As settlers moved west, the patterns multiplied. The Puget Sound felling ax came out of the big timber of the west coast, and on a 44-inch handle its narrow, elongated edge let lumberjacks reach deep into large-diameter timber. The manual puts the peak of American ax manufacturing in the early to mid 20th century and the decline from the 1940s, when war retooling and then the chain saw cut into it. Axes remain companion tools to saws, used mostly to drive wedges and not to chop wood.
The crosscut saw
Saws That Sing, a Forest Service guide to crosscut saws first issued in December 2004 and revised in June 2012, says the crosscut saw did not come into common use in Europe until the mid-15th century. Early saws were rectangular with handles fitted into sockets at each end, and had a plain or peg tooth. Over the next 400 years many national patterns developed, and as late as 1900 the plain and M tooth patterns were the most common in Europe.
Imported saws were used in Colonial America and were being made there by the mid-1800s. The guide says saws were not used for felling timber until about the 1880s. It calls 1880 to 1930 the golden age of crosscut saws. The machinery to make vintage saws began to disappear by the 1950s as power saws took over, and no taper-ground crosscut saws are made today.
The undercut
For felling, the guide describes the conventional undercut, also called the face cut, as two cuts, with a third cut forming the back cut. The undercut and back cut form the hinge that controls the direction of fall. The undercut can be chopped out with an ax, made with a crosscut saw, or made with a horizontal saw cut and a face chopped out with an ax. The guide calls the last of these often the preferred method, and says the ax is often the best tool for the sloping cut. The ax manual agrees on the pairing: sawyers felling with crosscut saws used an ax to chop out their sloping cut.
Powered saws and the chain
The ax manual says motorized saws date back to the late 1800s but were large and heavy. The drag saw was the most common, and loggers used it to buck logs with a vertical cutting motion. Early chain saws became available in the 1920s but were unreliable and could make only horizontal cuts, because the carburetors of the era prevented diagonal cuts. Sawyers still needed axes for the sloping cut. In the 1940s and early 1950s, better carburetors and smaller, lighter motors made chain saws more manageable and reliable.
Ellis Lucia's article in the Journal of Forest History for July 1981, adapted from his book The Big Woods, gives the saw chain side. The first chain saw patent went to Harvey Brown of New York City in 1858. A hand-operated chain saw was patented in England in 1900 by William Stanley of South Norwood. In 1905 a gasoline-powered chain saw was tested in the redwood forests near Eureka, California, and cut a ten-foot log in four and a half minutes. Charles Wolf brought out what the article ranks as the first successful portable chain saw in 1920, in three sizes of 70 to 90 pounds. Andreas Stihl in Germany built a two-man chain saw of 140 pounds in 1925 and began exporting a 46-pound saw in 1936.
The article says Joe Cox, a logger and machinist, designed a chain after watching the cutting action of the timber beetle larva Ergates spiculatus, which cut left and right instead of scratching straight ahead. He founded Oregon Saw Chain Corporation in 1947, and the firm sold US$300,000 of saw chain in its first year. Renamed Omark in 1957, it employed 4,400 people by 1980 in 17 plants in five countries, with sales above US$250 million. Lucia wrote that crosscut saws had been the one holdout of an age that was almost gone, and that loggers were still felling with the falling ax and crosscut saw as late as the mid-1940s. Other saw history is in the chainsaw history timeline and the guide to vintage saws and safety standards.
Sources
- USDA Forest Service, One Moving Part: The Forest Service Ax Manual, Chapter 3, A Brief History of the Ax, read October 21, 2026
- USDA Forest Service Missoula Technology and Development Center, Saws That Sing: A Guide to Using Crosscut Saws, December 2004, revised June 2012, read October 21, 2026
- Forest History Society, Ellis Lucia, A Lesson from Nature: Joe Cox and His Revolutionary Saw Chain, Journal of Forest History, July 1981, read October 21, 2026