Hydraulic hoses on tree machines: examination and replacement rules in regulator and standards text
No opened regulator text sets a hose replacement date. Britain's PUWER sets maintenance and inspection duties for work equipment, OSHA's 1910.269 has hose pressure and kink wording, and SAE J1273 covers hose replacement and storage.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The named regulators and standards bodies are described here as published. It is not training and does not teach the work. The texts are the Provision and Use of Work Equipment Regulations 1998 (PUWER) with the HSE guidance, an HSE safety alert on hydraulic injection, 29 CFR 1910.269, and the SAE catalogue entry for J1273. None of them is a tree-specific hose rule. Related hazards are covered in the guide to hydraulic injection and stored energy.
At a glance
| Text | What it says about hoses or hydraulic equipment |
|---|---|
| PUWER regulation 5 (Great Britain) | Work equipment must be maintained in an efficient state, in efficient working order and in good repair |
| PUWER regulation 6 (Great Britain) | Equipment exposed to deterioration liable to cause dangerous situations is inspected at suitable intervals and after exceptional circumstances |
| 29 CFR 1910.269(i)(4) | Safe operating pressures of hydraulic tools, hoses, valves, pipes, filters and fittings may not be exceeded; hoses may not be kinked |
| SAE J1273 (October 2021) | Recommended practice for selection, routing, fabrication, installation, replacement, maintenance and storage of hydraulic hose assemblies |
Great Britain: PUWER and the HSE guidance
The HSE publishes PUWER with an Approved Code of Practice and guidance as publication L22, addressed to employers and anyone responsible for the safe use of work equipment. HSE's PUWER pages cover inspection of work equipment, maintenance, training and competence, and mobile work equipment. The text of the Regulations does not use the word hose.
Regulation 5(1) puts the duty on every employer to keep work equipment maintained in an efficient state, in efficient working order and in good repair. Where machinery has a maintenance log, regulation 5(2) requires the log to be kept up to date. Regulation 6(2) covers equipment exposed to conditions that cause deterioration liable to result in dangerous situations. It is inspected at suitable intervals and each time exceptional circumstances liable to jeopardise its safety have occurred, so that deterioration is detected and remedied in good time. Regulation 6(3) requires the result to be recorded and kept until the next inspection. Regulation 6(5) lists equipment outside regulation 6, including work equipment for lifting loads including persons.
The HSE hydraulic injection alert
HSE safety alert FOD 4-2014, issued on September 23, 2014, concerns hydraulic injection injury. It records a fatality in which a grease fitting on a piling rig track detached and released grease under high pressure. It defines the injury as skin broken by a jet of fluid under pressure. It reports serious cases at pressures over 100 bar (1450 psi) and says anecdotal evidence points to injury at pressures as low as 7 bar (101.5 psi).
The alert says injection injury often follows failure of a component, leaving equipment pressurised and leaking while still in use. It states that fittings replaced on a pressurised system should match the original manufacturer's specification, and that verifying the replacement should be regarded as a pressure test. It cites BS EN ISO 4413, the general rules for hydraulic fluid power systems. It notes that without medical treatment the victim may feel intense throbbing pain after four to six hours.
United States: 29 CFR 1910.269
Section 1910.269 applies, except paragraph (r)(1), to line-clearance tree trimming done by qualified employees, meaning work to clear space around electric lines or equipment for the organisation that operates them. For trimmers who are not qualified employees it lists only paragraphs (a)(2), (a)(3), (b), (c), (g), (k), (p) and (r). The hydraulic wording sits in paragraph (i)(4), which is not on that shorter list.
Paragraph (i)(4)(i) says safe operating pressures for hydraulic and pneumatic tools, hoses, valves, pipes, filters and fittings may not be exceeded. Its note says that if hazardous defects are present, no operating pressure is safe and the equipment may not be used. Absent defects, the maximum rated operating pressure is the maximum safe pressure. Paragraph (i)(4)(v) says pressure is released before connections are broken unless quick-acting, self-closing connectors are used. Paragraph (i)(4)(vi) says employees do not use any part of the body to locate or stop a hydraulic leak, and (vii) says hoses may not be kinked.
SAE J1273
SAE International lists J1273, Recommended Practices for Hydraulic Hose Assemblies, revised October 28, 2021 and first issued in September 1979. Its scope covers guidelines for selection, routing, fabrication, installation, replacement, maintenance and storage of hose and hose assemblies for hydraulic fluid-power systems. SAE adds that many of the practices may suit other hoses and systems. The catalogue entry carries no clause text, and a hose replacement interval does not appear on it.
Sources
- HSE, Provision and Use of Work Equipment Regulations 1998 (L22), Approved Code of Practice and guidance, read October 19, 2026
- HSE, Provision and Use of Work Equipment Regulations 1998 (PUWER), page updated March 16, 2023, read October 19, 2026
- legislation.gov.uk, The Provision and Use of Work Equipment Regulations 1998, regulations 5 and 6, as made, read October 19, 2026
- HSE, Safety alert FOD 4-2014, Hydraulic injection injury, September 23, 2014, read October 19, 2026
- eCFR, 29 CFR 1910.269, electric power generation, transmission and distribution, read October 19, 2026
- SAE International, J1273_202110, Recommended Practices for Hydraulic Hose Assemblies, catalogue entry, read October 19, 2026