Lanyard adjusters and positioners: device types and the maximum length stop in the codes
The UK industry code describes a rope adjustment device that can be threaded on to a lanyard. The New South Wales code wants a maximum length stop built in, and the New Zealand code wants a means to stop the device slipping off the end.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
The facts here come from three codes and one standards body on lanyard adjusters. It is not training and does not teach the work. They are the UK Industry Code of Practice for Arboriculture, Tree Work at Height (ICoP, Edition 2, May 2020), the SafeWork NSW Tree works code (March 2026) and the WorkSafe New Zealand code, Safety and Health in Arboriculture (November 2012). The BSI standards page for BS EN 358:2018 gives the product scope. For lanyard types in general, see lanyards and flip lines by type.
Device types in the codes
| Source | Item | Wording |
|---|---|---|
| ICoP 3.10.6.6 | Rope adjustment device | A device that may be applied at a mid-point, or threaded on to the end of personal fall protection components such as a lanyard, allowing the operator to introduce or remove slack within a system |
| ICoP 3.10.6.10 | Lanyard | Fixed or adjustable. An adjustable lanyard is preferred in the most common use because it minimises slack and so the distance and consequences of a fall |
| SafeWork NSW 4.4 | Work positioning harness | Should be used in conjunction with adjustable lanyards or pole straps |
| WorkSafe NZ glossary | Safety lanyard, also called strop or flip line | An adjustable rope or strop designed as a work positioning aid, with all materials meeting the minimum strength of an arborist climbing line |
| BS EN 358:2018 | Belts and lanyards for work positioning or restraint | Requirements, testing, marking and maker information for belts and lanyards for work positioning or restraint |
The stop at the end of the lanyard
The wording differs by code.
- SafeWork NSW, section 4.5. The code lists points to consider for adjustable lanyards. One is that lanyards should incorporate a maximum length stop as an integral part of the lanyard.
- WorkSafe New Zealand, section 3.2. Lanyards should have an effective means to prevent the friction hitch or device from slipping off the end of the lanyard.
- ICoP 3.10.6.6. The code says the device may be applied at a mid-point or threaded on to the end of a lanyard, and sets conditions on how it behaves. It does not use the word stop in that clause.
The New Zealand and New South Wales texts describe the same feature from two sides. One names the stop. The other names what the stop prevents.
What the codes require of the adjuster
ICoP 3.10.6.6 sets four conditions. The device grabs positively and reliably at each use. The rope diameter and type match the maker's specification. The device operates under control and acts predictably across work and rescue scenarios. The code shows a preference for devices that let the operator apply or release pressure gradually.
For the lanyard itself, clause 3.10.6.10 says it must be compatible with the connectors, have a means of adjustment and a suitable length, and adjust efficiently, positively and reliably in length under load. It must be attached to the harness to prevent torsion or cross-loading, and have a minimum breaking strength of at least 15 kN.
Other points in SafeWork NSW and New Zealand
The SafeWork NSW code also says the orientation of connection hardware should not encourage twisting or roll-out. Webbing should be retired if there are visible cuts. Wire or wire core lanyards should not be used in an electrical environment. WorkSafe New Zealand says friction hitches and work-positioning lanyards used in a climbing system shall meet the minimum strength standards for arborist climbing lines.
The standard
BSI describes BS EN 358:2018 as applying to belts and lanyards intended for work positioning or restraint. It supersedes BS EN 358:1999, which is withdrawn. The 2018 edition changed the definition of work positioning lanyard and added new definitions for restraint lanyard and maximum rated load. BSI notes that fixed-length restraint lanyards not integrated into a belt are not covered and fall under EN 354.
Sources
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 21, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 21, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 21, 2026
- BSI Knowledge, BS EN 358:2018 Belts and lanyards for work positioning or restraint, published December 31, 2018, read October 21, 2026