Limb walking and moving in the crown: NZ code, AHCARB319, NZQA and the ITCC
Branch walking is a graded outcome in New Zealand unit standard 2774, and the limb walk is a station in the ITCC Work Climb. The New Zealand code covers bypassing branches on a lanyard. No code opened gives a limb size or load limit.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work.
Credits: WorkSafe New Zealand material is summarised from its Approved Code of Practice for Safety and Health in Arboriculture (November 2012), with the source acknowledged.
The New Zealand code
The WorkSafe New Zealand code, section 3.2.2, says a climber is tied in or secured to the tree while ascending and stays tied in until work is complete and the climber is back on the ground. Supplementary anchor points are used where a fall or swing that may cause injury is possible.
The same section covers bypassing branches. The safety lanyard is never unclipped except to bypass branches. In that case a second lanyard or line is fastened free of the obstructing branch and checked for security before the first lanyard is unclipped. Lanyards should also have a means to stop the friction hitch or device slipping off the end.
Section 3.1.6 adds that the climber is attached by two anchor points when making cuts aloft.
The Australian unit
AHCARB319 Use arborist climbing techniques is a unit of competency in the Australian AHC training package, release 1. Its application statement names climbing techniques for mobility in the canopy of trees to acquire a safe work position.
Element 3 covers accessing and working in the tree. Its criteria include selecting anchor points for load bearing and access. They also include ascending and reaching work positions in the tree crown with a system suited to the task and the tree structure. Safe clearance from hazards and from power lines is part of the same element. The unit does not use the words limb walking.
The NZQA standards
NZQA unit standard 2774, version 8, is titled Climb difficult trees, branch walk and undertake aerial rescue above 15 metres in arboriculture situations. It is at level 4 and carries 10 credits.
Outcome 4 is setting climbing lines for branch walking. Its criteria are selecting roping points that give a safe, unobstructed rope, and setting climbing lines into them. The listed range is a single roping point, re-direct points and a double tie-in system.
Outcome 5 is branch walking on branches over 10 metres above the ground. The criteria are performing a branch walk safely, and identifying and using secondary roping or re-direction points so that suitable anchors can be created in the tree for safe working positions.
The prerequisite is unit standard 31185, which covers climbing equipment, knots, inspecting the tree and site for hazards, and a climb of at least 12 metres. Neither standard sets a limb size or a load.
The ITCC Work Climb
The International Tree Climbing Championship rule book of 2022 is a set of competition rules, not a work code. That edition is marked valid until July 1, 2024. In the Work Climb, section 3.2.6 has the competitor tied in with a climbing line and secured with a work-positioning lanyard at each station, including the limb walk, before ringing the bell.
Section 3.6, the limb walk station, uses a plumb bob to measure branch movement. Points are added for a walk without excessive movement. The competitor keeps at least one foot on the limb at all times. A competitor who loses control and falls, or swings from the limb, returns to the last point of contact.
The task order is to touch the starting mark with a foot, walk out, lanyard in, call a warning, ring the bell with the handsaw and walk back to the mark. The mark is at least 30 cm (12 in) wide. Rule 2.3.19 counts unmanaged slack, a loop hanging below the knees, as an infraction.
The ICoP on movement around the crown
The ICoP, 3.8.6, notes that the technique used to ascend may also be the one used to move around the canopy. Where two separate techniques are used, it lists what must be considered: their suitability and compatibility, the transition from one to the other, the proficient operator's movement around the tree, and achieving and maintaining safe work positions.
Gaps in the sources
The ICoP and the New Zealand code give no limb-walking criteria, and the Australian unit does not use the words. None of the codes or units opened gives a limb diameter, load or angle.
Sources
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, sections 3.1.6 and 3.2.2, read October 19, 2026
- Skills Insight, AHCARB319 Use arborist climbing techniques, release 1, Australian Training Package AHC, read October 19, 2026
- NZQA, unit standard 2774 version 8, Climb difficult trees, branch walk and undertake aerial rescue above 15 metres in arboriculture situations, read October 19, 2026
- NZQA, unit standard 31185 version 3, Demonstrate knowledge of climbing equipment, climb a tree and undertake one-person aerial rescue, read October 19, 2026
- International Tree Climbing Championship, Rule Book, 2022 edition, valid until July 1, 2024, copy hosted at suomenpuunhoidonyhdistys.fi, read October 19, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height (ICoP), second edition, May 2020, section 3.8.6, read October 19, 2026