ArbNation Join free

Line-clearance tree trimmer in OSHA 1910.269: the definitions and the training wording

OSHA 1910.269 defines a line-clearance tree trimmer by training or experience, and separately defines a qualified employee. The 2014 rule added a three-item training list for trimmers who are not qualified employees.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The text is 29 CFR 1910.269 as published in the eCFR and on OSHA's website, and OSHA's April 11, 2014 final rule that revised the standard. The scope of 1910.269 for tree work is covered in the guide to 1910.269 and line-clearance tree trimming.

The definitions

Definitions in 29 CFR 1910.269(x)
TermDefinition in the standard
Line-clearance tree trimmerAn employee who, through related training or on-the-job experience or both, is familiar with the special techniques and hazards involved in line-clearance tree trimming
Qualified employeeAn employee knowledgeable in the construction and operation of the electric power generation, transmission and distribution equipment involved, along with the associated hazards
Line-clearance tree trimmingPruning, trimming, repairing, maintaining, removing or clearing trees, or cutting brush, within 3.05 m (10 ft) of electric supply lines and equipment at 50 kV or less to ground. Above 50 kV the distance is 3.05 m plus 0.10 m (4 in) for every 10 kV over 50 kV

Note 1 to the trimmer definition covers an employee in training. The employee is regularly assigned to a line-clearance tree-trimming crew and is undergoing on-the-job training. He or she has demonstrated an ability to perform duties safely at that level of training and works under the direct supervision of a line-clearance tree trimmer. Such an employee is considered a line-clearance tree trimmer for those duties.

Note 2 separates the trimmer from the qualified employee. A line-clearance tree trimmer is not a qualified employee under 1910.269 unless he or she has the training required for a qualified employee under paragraph (a)(2)(ii). Under the electrical work practices in subpart S, a line-clearance tree trimmer is considered a qualified employee. Tree trimming by such qualified employees is not subject to sections 1910.331 through 1910.335 when it is directly associated with electric power generation, transmission or distribution lines or equipment.

Scope for tree work

Paragraph (a)(1)(i)(E) brings in line-clearance tree trimming done to clear space around power lines or equipment on behalf of an organization that operates, or controls the operating procedures for, those lines or equipment. Qualified employees doing that work come under the entire standard except paragraph (r)(1). Trimmers who are not qualified employees come under paragraphs (a)(2), (a)(3), (b), (c), (g), (k), (p) and (r).

A note to the definition of line-clearance tree trimming places trimming for a homeowner or a commercial entity other than the operating organization outside the section. Trimming that is not for the purpose of clearing space around electric lines or equipment is also outside it.

Training wording in paragraph (a)(2)

Paragraph (a)(2)(i) requires every employee doing covered work to be trained in the safety practices that pertain to the job. The degree of training is set by the risk to the employee from the hazard involved. Paragraph (a)(2)(ii) adds five areas for each qualified employee:

  • distinguishing exposed live parts from other parts of electric equipment;
  • determining the nominal voltage of exposed live parts;
  • the minimum approach distances for the voltages involved and the skills to maintain them;
  • the proper use of special precautionary techniques, personal protective equipment, insulating and shielding materials and insulated tools;
  • recognising the electrical hazards the employee may be exposed to and the skills to control or avoid them.

Paragraph (a)(2)(iii) applies to each line-clearance tree trimmer who is not a qualified employee. That trimmer must be trained and competent in the first three of those areas: telling live parts from other parts, determining nominal voltage, and the minimum approach distances with the skills to keep them. Paragraph (a)(2)(iv) has the employer determine, through regular supervision and inspections at least annually, that each employee follows the work practices. Paragraph (a)(2)(v) calls for retraining when supervision or inspection shows non-compliance, when new technology or procedures change the work practices, or when an employee must use practices not normally used in the regular job.

Paragraph (r)(1)

Paragraph (r)(1) does not apply to qualified employees. It requires a determination of the nominal voltage of lines before an employee climbs, enters or works around a tree. A second line-clearance tree trimmer must be within normal voice communication under three conditions. One is a trimmer approaching closer than 3.05 m (10 ft) to a conductor or apparatus energized above 750 volts. Another is limbs coming closer to lines above 750 volts than the distances in Tables R-5 to R-8. The third is roping needed to remove limbs from conductors or apparatus.

Trimmers keep the minimum approach distances in those tables. Branches touching energized conductors, or inside the table distances, may be removed only with insulating equipment. Ladders, platforms and aerial devices may not come closer than the table distances. Thunderstorms nearby, high winds, snow storms and ice storms are presumed to make the work too hazardous.

The 2014 final rule

OSHA published the final rule on electric power generation, transmission and distribution on April 11, 2014, at 79 FR 20315 to 20743. It took effect July 10, 2014, with some provisions carrying later compliance dates. In the preamble OSHA states that regular tree trimmers are subject to subpart S but are not covered by 1910.269, while line-clearance tree trimmers must comply with 1910.269.

The Utility Line Clearance Coalition and the Tree Care Industry Association asked OSHA to widen the definition of line-clearance tree trimming to all vegetation management for utilities. OSHA was not persuaded and kept the 3.05 m basis, with limited changes that broaden the scope somewhat. The preamble explains that the rule added training requirements for line-clearance tree trimmers in paragraph (a)(2)(iii). To count as a line-clearance tree trimmer who is a qualified employee for subpart S, an employee must meet the definition and have training that meets that paragraph.

Sources