Log scale rules by place: Washington, Idaho, Oregon, British Columbia and the UK
Washington and Idaho name Scribner Decimal C in their rules, Oregon calls it the main rule, and British Columbia requires cubic metres under its metric scale. The UK Hoppus tables use quarter-girth in inches.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. A log rule is a table that turns log diameter and length into a volume. The Oregon Department of Forestry says a rule does not give an accurate measure of the board feet that will be sawn from a log, and that the gap between scale and lumber tally is called overrun or underrun.
Rule by place
| Place | Rule and authority |
|---|---|
| Washington | Scribner Decimal C, in WAC 458-40-680 (Department of Revenue, timber excise tax) |
| Idaho | Scribner Decimal C or cubic volume, in IDAPA 20.06.01 (Board of Scaling Practices) |
| Oregon | Scribner Decimal C, named the main rule by the Department of Forestry |
| British Columbia | British Columbia metric scale in cubic metres, in Forest Act section 96 |
| United Kingdom | Hoppus tables, with a metric equivalent from the Forestry Commission |
| Ireland | The Central Statistics Office survey asks for tonnes and cubic metres |
Washington
WAC 458-40-680 sets the scaling standard for timber excise tax. In stumpage value areas 1, 2, 3, 4, 5 and 9, the standard is the Scribner Decimal C rule as described in the Official Log Scaling and Grading Rules of the Northwest Log Rules Advisory Group. In areas 6 and 7 it is Scribner Decimal C as described in the group's Eastside Log Scaling Handbook, with the current regional taper rules applied at the point of origin.
Sample scaling and special services scaling need prior written approval of the Department of Revenue for tax reporting. A sample must meet a board foot variation limit of plus or minus 2.5 percent standard error at the 95 percent confidence level. The rule also sets conversion factors into Scribner volume:
- A cord with an average scaling diameter of 8 inches or more converts at 400 board feet in areas 1 to 5 and 9, and 470 in areas 6 and 7. Smaller logs convert at 330 and 390.
- Firewood converts at 3 tons per cord.
- A lumber tally from a portable mill is multiplied by 75 percent in areas 1 to 5 and 9, and 88 percent in areas 6 and 7.
- Timber scaled by the eastside handbook in western areas is reduced by 18 percent, and the reverse is increased by 18 percent.
Idaho
The Idaho Board of Scaling Practices incorporates the Idaho Log Scaling Manual, 2008 edition, and the Idaho Cubic Log Scaling Manual, 2020 edition. It defines Decimal C as a rule that uses tens of board feet as its unit, so one decimal C equals ten board feet, and the Idaho volumes are Scribner. It defines cubic volume as a rule that uses the Smalian formula, rounded to a tenth of a cubic foot.
Section 500 allows scaling by Scribner decimal C or by cubic volume. Any other method is decided by the Board on written request. Gross volume measured another way is converted to an equivalent decimal C or cubic volume.
Oregon
The Oregon Department of Forestry says the Scribner log rule and its Decimal C modification are the most common rule in use, and the main rule used in Oregon and Washington by private industry and state agencies. In Decimal C the volume is taken to the nearest 10 board feet and the last digit dropped. It states that the department usually uses board feet per thousand board feet (MBF), and that the Forest Service and BLM sometimes use cubic feet.
It separates west-side long log scale, with a maximum scaling length of 40 feet, from east-side short log scale, with a maximum of 20 feet. West-side scaling adds 1 inch every 10 feet to the diameter for taper, and east-side scaling measures the actual taper.
British Columbia
Forest Act section 96 says a person who scales timber must express the scale in cubic metres, or another metric unit the minister requires for special forest products. A scale in cubic metres is known as British Columbia metric scale. The Ministry of Forests Scaling Manual, revised by memorandum of November 18, 2009, calls it the official scale rule under the Act. It uses Smalian's formula for individual logs and records net firmwood volume in cubic metres. The manual says all timber harvested from Crown and private land must be scaled.
United Kingdom and Ireland
The Forestry Commission published a metric volume ready reckoner for round timber on January 31, 1970. Forest Research lists it as an archive publication. It calls the tables the metric equivalent of the old established Hoppus tables, used in exactly the same way, with mid-diameters in centimetres in place of mid-quarter girth in inches, lengths in metres and volumes in cubic metres.
The Irish Central Statistics Office does not name a log rule. Its Roundwood Removals Survey asks for quantities in tonnes overbark and in cubic metres where both are available. The questionnaire sorts Irish roundwood by top diameter and length.
Sources
- Washington State Legislature, WAC 458-40-680 Timber excise tax, approved scaling and grading methods, read October 16, 2026
- Idaho Administrative Rules, IDAPA 20.06.01 Rules of the Idaho Board of Scaling Practices, read October 16, 2026
- Oregon Department of Forestry, Log Term Definitions, undated PDF, read October 16, 2026
- British Columbia, Forest Act RSBC 1996 c.157 Part 6 Timber Scaling, current to October 6, 2026, read October 16, 2026
- British Columbia Ministry of Forests and Range, Scaling Manual with memorandum of November 18, 2009, read October 16, 2026
- Forest Research, Metric volume ready reckoner for round timber (Forestry Commission, 1970, archive), read October 16, 2026
- Central Statistics Office Ireland, Roundwood Removals Survey 2025 questionnaire, read October 16, 2026