ArbNation Join free

Lorry-mounted loader cranes in the UK: BS EN 12999, LOLER and operator training

A lorry loader is a hydraulic crane built to BS EN 12999 and examined under LOLER every 12 months, or every 6 when it lifts people. HSE has also issued a safety notice on three deaths from tilting stabilisers.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The facts on this page come from BSI and HSE. It is not training and does not teach the work. Crane operator licences and lifting rules by country are in cranes in tree work.

BS EN 12999: the loader crane standard

BSI lists BS EN 12999:2020, Cranes, Loader cranes. It sets minimum requirements for the design, calculation, examinations and tests of hydraulic-powered loader cranes and their mountings on vehicles or static foundations. It also applies to loader cranes fitted with special tools or interchangeable equipment, such as a grapple.

The standard applies to loader cranes meant for installation on these carriers.

  • Road vehicles, including trailers, that can carry loads.
  • Tractors, road or agricultural, where only a towed trailer can carry goods.
  • Demountable bodies carried by any of those.
  • Other carriers, such as separate loaders, crawlers, rail vehicles and non-seagoing vessels.
  • Static foundations.

It does not cover hazards from lifting persons, loader cranes on sea-going vessels, or articulated boom cranes built as integral parts of special equipment such as forwarders. BSI adds that crane use for lifting people can fall under specific national regulations. BS EN 12999:2020 supersedes the 2011+A2:2018 edition, which is withdrawn. The two main changes are a new reference to EN ISO 13849-1:2015 and a better stability test subclause.

LOLER: examination and evidence

HSE's approved code of practice L113 lists a loader crane fitted to a lorry, such as one used to raise bins for deliveries, among examples of equipment the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) cover. It adds that LOLER applies to all lifting equipment used for work, even equipment made and put into use before 1998.

Regulation 9 sets the thorough examination periods for equipment exposed to conditions that cause deterioration.

EquipmentThorough examination
Lifting equipment for lifting persons, or an accessory for liftingAt least every 6 months
Other lifting equipmentAt least every 12 months
Either kind, under an examination schemeAs the scheme sets
After exceptional circumstances that could jeopardise safetyEach time they occur

Under regulation 9(4), lifting equipment cannot leave an employer's undertaking, or be used in an undertaking it was obtained from, unless it comes with physical evidence that the last required thorough examination was done. A first examination before service is needed unless the equipment is unused and its declaration of conformity is no more than 12 months old.

L113 also says some road-going equipment, such as lorry loaders, is subject to MOT examination. LOLER and PUWER examinations serve a different purpose and do not replace the MOT. For lifting machinery whose safe working load changes with radius, L113 says the load should be marked or adequate information provided to the user, and suggests a rated capacity indicator or limiter where the hazard is significant.

HSE safety notice on tilting stabilisers

HSE bulletin EPD04-2023, issued in December 2023, covers lorry loaders with powered tilting stabilisers, also called swing-up or rotating stabilisers. On some machines a person can be crushed against the bodywork when the stabiliser retracts. HSE knows of three fatal incidents in Great Britain since 2019 in which an operator was struck by a stabiliser leg only part-rotated to about horizontal.

The notice tells owners to seek safety improvements from manufacturers. It gives three examples: software changes that stop retraction unless the leg is vertical, interlocks with the same effect, and removing fixed base levers so only remote control is used. It asks for residual risk warning decals to be present and visible, and for the crushing hazard to appear in risk assessments and lift plans.

On operators and training, the notice says users should see that operators are competent, know the stabiliser type fitted and have been trained in its correct use. Familiarisation training, such as at new vehicle handover or when an operator moves to another vehicle, should cover the notice. The notice lists safe working points: leg pinned or locked vertical before the beam moves, operators watching all stabiliser movements, tilt-up kept separate from beam retraction, and nobody positioned in the danger zones.

Sources