Machine glossary for wood chippers and aerial lifts: terms as OSHA, HSE and CEN use them
More than twenty terms for wood chippers and vehicle-mounted aerial lifts, as OSHA and the CEN chipper standard print them: infeed chute, feed control bar, bottom feed stop bar, articulating boom platform.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The chipper terms come from OSHA Safety and Health Information Bulletin 04-16-2008, HSE's information sheet AIS38 and the scope of EN 13525:2020. The aerial lift terms are the definitions in 29 CFR 1910.67(a).
Wood chipper terms
OSHA's bulletin describes a chipper as a powered feed mechanism, knives mounted on a rotating disc or drum, and an internal combustion engine. The knives usually turn at 1,000 to 2,000 revolutions per minute. The bulletin is advisory and creates no new legal obligations.
| Term | As the source prints it | Source |
|---|---|---|
| Infeed chute | Where employees feed branches by hand | OSHA bulletin |
| Feed rollers | At the end of the infeed chute, they grab branches and force them into the knives | OSHA bulletin |
| Discharge chute | Where the drum and knives force the chips out | OSHA bulletin |
| Feed control bar | A mechanical bar across the top and sides of the infeed chute that starts the feed rollers when pulled. Pushed to neutral it stops them, pushed toward the discharge spout it reverses them | OSHA bulletin |
| Bottom feed stop bar | A pressure-sensitive device on the lower edge of the feed table that cuts all power at 34 pounds of force. OSHA reports one manufacturer fitting it, and that maker says it cannot be retrofitted to older models | OSHA bulletin |
| Emergency pull ropes | Ropes or cables on both sides of the infeed throat that reverse the feed rollers when pulled | OSHA bulletin |
| Feed tray extension | A longer or fold-down tray that can lengthen the infeed area by as much as four feet | OSHA bulletin |
| Panic bar | A bar, separate from the feed control bar, that stops the hydraulic system running the feed rollers when grabbed | OSHA bulletin |
| Rubber curtain or flaps | Flexible flaps across the front of the infeed chute that warn hands away and stop objects kicking back | OSHA bulletin |
| Discharge spout deflector | A guard that redirects chips into a truck or away from workers | OSHA bulletin |
| Hood safety latch | An interlock that stops the chipper starting until the hood is locked and stops the hood opening before the disc or drum has stopped | OSHA bulletin |
| Safety watch | An employee stationed near the emergency shut-off devices while others feed material | OSHA bulletin |
Power-fed chippers in HSE and CEN wording
HSE's AIS38 is titled Power-fed mobile wood chippers: operator protection at infeed chutes. The 2013 revision, coded AIS38(rev1), is for people in arboriculture and forestry. It outlines the protection needed at the infeed chutes and describes the types of guarding and protection devices, their design, position and function, plus training on feeding chippers.
EN 13525:2020, Forestry machinery: Wood chippers: Safety, was published by CEN on August 17, 2020, and confirmed on December 4, 2025. It replaced EN 13525:2005+A2:2009. Its scope covers self-propelled, mounted, semi-mounted and trailed wood chippers used in forestry, agriculture, horticulture and landscaping.
| Scope term in EN 13525 | What the scope says |
|---|---|
| Manually loaded chipper | Used when stationary and loaded with wood by hand through a horizontal or near horizontal infeed chute |
| Infeed components | The chipping components themselves, or separate rollers or conveyors built into the infeed chute |
| Lower Protective Device | Named in an exclusion: machines whose infeed chute has an extension table or integrated conveyor protruding beyond the chute's outermost lower edge and the Lower Protective Device are outside the scope |
| Outside the scope | Vertical infeed chute chippers, machines loaded only mechanically, and shredder-chippers covered by EN 13683 |
Aerial lift terms in 29 CFR 1910.67
OSHA's vehicle-mounted platform rule defines its words in paragraph (a). The rule uses the word outriggers without defining it: brakes are set and outriggers, when used, sit on pads or a solid surface, and they are stowed before the lift travels.
| Term | Definition in the rule |
|---|---|
| Aerial device | Any vehicle-mounted device, telescoping or articulating or both, used to position personnel |
| Aerial ladder | An aerial device made of a single or multiple-section extensible ladder |
| Articulating boom platform | An aerial device with two or more hinged boom sections |
| Extensible boom platform | An aerial device, ladders excepted, with a telescopic or extensible boom. A telescopic derrick with a personnel platform counts as one when used with that platform |
| Insulated aerial device | An aerial device designed for work on energized lines and apparatus |
| Mobile unit | An aerial device, its vehicle and related equipment together |
| Platform | Any personnel-carrying basket or bucket that is a component of an aerial device |
| Vertical tower | An aerial device that raises a platform along a near-vertical axis |
| Vehicle | Any carrier that is not manually propelled |
Sources
- US Occupational Safety and Health Administration, Hazards of Wood Chippers, Safety and Health Information Bulletin SHIB 04-16-2008, read October 15, 2026
- Health and Safety Executive (Great Britain), Power-fed mobile wood chippers: operator protection at infeed chutes, AIS38(rev1), 2013, read October 15, 2026
- CEN, EN 13525:2020 Forestry machinery, wood chippers, safety, scope and status page on Genorma, read October 15, 2026
- US eCFR via OSHA, 29 CFR 1910.67 vehicle-mounted work platforms, definitions in paragraph (a), read October 15, 2026