ArbNation Join free

Machine glossary for wood chippers and aerial lifts: terms as OSHA, HSE and CEN use them

More than twenty terms for wood chippers and vehicle-mounted aerial lifts, as OSHA and the CEN chipper standard print them: infeed chute, feed control bar, bottom feed stop bar, articulating boom platform.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The chipper terms come from OSHA Safety and Health Information Bulletin 04-16-2008, HSE's information sheet AIS38 and the scope of EN 13525:2020. The aerial lift terms are the definitions in 29 CFR 1910.67(a).

Wood chipper terms

OSHA's bulletin describes a chipper as a powered feed mechanism, knives mounted on a rotating disc or drum, and an internal combustion engine. The knives usually turn at 1,000 to 2,000 revolutions per minute. The bulletin is advisory and creates no new legal obligations.

TermAs the source prints itSource
Infeed chuteWhere employees feed branches by handOSHA bulletin
Feed rollersAt the end of the infeed chute, they grab branches and force them into the knivesOSHA bulletin
Discharge chuteWhere the drum and knives force the chips outOSHA bulletin
Feed control barA mechanical bar across the top and sides of the infeed chute that starts the feed rollers when pulled. Pushed to neutral it stops them, pushed toward the discharge spout it reverses themOSHA bulletin
Bottom feed stop barA pressure-sensitive device on the lower edge of the feed table that cuts all power at 34 pounds of force. OSHA reports one manufacturer fitting it, and that maker says it cannot be retrofitted to older modelsOSHA bulletin
Emergency pull ropesRopes or cables on both sides of the infeed throat that reverse the feed rollers when pulledOSHA bulletin
Feed tray extensionA longer or fold-down tray that can lengthen the infeed area by as much as four feetOSHA bulletin
Panic barA bar, separate from the feed control bar, that stops the hydraulic system running the feed rollers when grabbedOSHA bulletin
Rubber curtain or flapsFlexible flaps across the front of the infeed chute that warn hands away and stop objects kicking backOSHA bulletin
Discharge spout deflectorA guard that redirects chips into a truck or away from workersOSHA bulletin
Hood safety latchAn interlock that stops the chipper starting until the hood is locked and stops the hood opening before the disc or drum has stoppedOSHA bulletin
Safety watchAn employee stationed near the emergency shut-off devices while others feed materialOSHA bulletin

Power-fed chippers in HSE and CEN wording

HSE's AIS38 is titled Power-fed mobile wood chippers: operator protection at infeed chutes. The 2013 revision, coded AIS38(rev1), is for people in arboriculture and forestry. It outlines the protection needed at the infeed chutes and describes the types of guarding and protection devices, their design, position and function, plus training on feeding chippers.

EN 13525:2020, Forestry machinery: Wood chippers: Safety, was published by CEN on August 17, 2020, and confirmed on December 4, 2025. It replaced EN 13525:2005+A2:2009. Its scope covers self-propelled, mounted, semi-mounted and trailed wood chippers used in forestry, agriculture, horticulture and landscaping.

Scope term in EN 13525What the scope says
Manually loaded chipperUsed when stationary and loaded with wood by hand through a horizontal or near horizontal infeed chute
Infeed componentsThe chipping components themselves, or separate rollers or conveyors built into the infeed chute
Lower Protective DeviceNamed in an exclusion: machines whose infeed chute has an extension table or integrated conveyor protruding beyond the chute's outermost lower edge and the Lower Protective Device are outside the scope
Outside the scopeVertical infeed chute chippers, machines loaded only mechanically, and shredder-chippers covered by EN 13683

Aerial lift terms in 29 CFR 1910.67

OSHA's vehicle-mounted platform rule defines its words in paragraph (a). The rule uses the word outriggers without defining it: brakes are set and outriggers, when used, sit on pads or a solid surface, and they are stowed before the lift travels.

TermDefinition in the rule
Aerial deviceAny vehicle-mounted device, telescoping or articulating or both, used to position personnel
Aerial ladderAn aerial device made of a single or multiple-section extensible ladder
Articulating boom platformAn aerial device with two or more hinged boom sections
Extensible boom platformAn aerial device, ladders excepted, with a telescopic or extensible boom. A telescopic derrick with a personnel platform counts as one when used with that platform
Insulated aerial deviceAn aerial device designed for work on energized lines and apparatus
Mobile unitAn aerial device, its vehicle and related equipment together
PlatformAny personnel-carrying basket or bucket that is a component of an aerial device
Vertical towerAn aerial device that raises a platform along a near-vertical axis
VehicleAny carrier that is not manually propelled

Sources