ArbNation Join free

Machine incident library from regulators (chipper, grinder, crane, lift, truck)

NIOSH counted 11 deaths near mobile wood chippers from 1992 to 1997. SafeWork NSW released two scissor lift tip-overs from 2020, and WorkSafe WA issued a 2021 alert on a boom lift failure during tree lopping.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

No victim is named and no firm is named.

Wood chippers: NIOSH Hazard ID 8

The National Institute for Occupational Safety and Health published Hazard ID 8, publication 99-145, in August 1999. It cites the Bureau of Labor Statistics Census of Fatal Occupational Injuries: 11 workers died from 1992 through 1997 while working near mobile wood chippers. In seven incidents the worker was caught by the feed mechanism and pulled through the knives. In four, the worker was struck by a hood that separated from the machine after being improperly opened or closed while the knives were still rotating.

NIOSH added two reports of deaths from 1998, both investigated under its Fatality Assessment and Control Evaluation program. One case study describes a groundsman caught by the feed mechanism while feeding short branches, with the chipper's infeed hopper the point of entry. The other describes a laborer at a waste-management facility struck by a flying disc hood. The chipper had been converted to a stationary machine and the hood was opened before the disc stopped. Investigators found damaged hood hinges allowing excessive side movement.

NIOSH's recommendations for employers include testing emergency shut-off devices before use, daily inspection for broken or missing hood latches and pins, and stopping all internal parts before the hood is opened.

Lifts: SafeWork NSW tip-over release

SafeWork NSW's incident information release covers two scissor type MEWP tip-overs in 2020.

  • Kingswood, 17 April 2020: a worker on a manually propelled scissor MEWP about 3 metres high was fixing cladding panels with a battery screw gun. The force of drilling contributed to the tip-over. The worker had bruising to an arm and shoulder.
  • Tamworth, 20 July 2020: an electrician and an apprentice raised a scissor MEWP to just below 6 metres on a concrete path to remove 34 metres of conduit. The conduit was lifted overhead and dropped onto the platform handrail. Its weight and momentum tipped the MEWP with both workers inside. Both had spinal fractures, and one had a fractured eye socket.

The release's safety information gives a maximum manual side force of 200 N, which it equates to a 20 kg force at waist height. It also mentions a high-risk work licence for boom type MEWPs with a boom length over 11 metres, and outdoor wind ratings shown on the compliance plate.

Lifts: WorkSafe WA boom failure

WorkSafe Western Australia's safety alert 03/2021, published 3 March 2021, concerns November 2020. Two workers were tree lopping from a truck-mounted boom lift when the boom suffered a major structural failure. The metal support separated from the fibreglass joint, and one worker was seriously injured.

WorkSafe lists possible contributing factors: a fibreglass insulated boom whose metal-to-fibreglass join is glued, annual inspections that did not identify signs of impending failure, and potential design or manufacturing defects in the glued connection. It states the findings are preliminary, and that it is liaising with regulators in other jurisdictions. The alert refers to inspection by a competent person under the manufacturer's instructions and AS/NZS 2550.10-2006.

Cranes, trucks and trailers: SafeWork NSW alert titles

SafeWork NSW's machinery, plant and equipment safety alerts list has titles on tower cranes, including erecting, climbing, dismantling and fire. It also lists using mobile cranes in pick and carry operations, mobile plant near power lines and towing trailers. Others are falls from flatbed trucks and trailers, and heavy vehicles or trailers hitting or crushing workers. The list prints titles only.

To correct or remove an entry, write to the address at the foot of this page.

Sources