ArbNation Join free

Measurement words in tree surveys: DBH, crown ratio, height to crown base and more

Thirty-odd words from tree surveys, defined as the Urban FIA field guide and the i-Tree Eco manual define them: diameter, length, crown, dieback and cover terms, plus the title and edition of BS 5837.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

The USDA Forest Service National Urban FIA Plot Field Guide, Version 9.5, September 2025, defines most of these words. The i-Tree Eco User's Manual, version 6.0, September 22, 2021, defines the rest. The two do not always define a word the same way.

Diameter and stem words

Diameter and stem terms
TermWhat the source recordsSource
DBHDiameter at breast height. Measured 4.5 feet above the ground line on the uphill side. Each reading is rounded down to the last 0.1 inch, so 3.68 inches is recorded as 3.6Urban FIA
DBH in EcoStem diameter at breast height, 4.5 feet above the ground. One of the two fields every tree must carry, with speciesEco manual
DRCDiameter at root collar. Taken at the ground line or the stem root collar, whichever is higher, for species listed as needing it. For several stems DRC is the square root of the sum of the squared stem diametersUrban FIA
Calipers and biltmore sticksAlternative tools the guide names for accurate measurement when vines cannot be pried off a trunkUrban FIA
SaplingA stem with a diameter of 1.0 inch through 4.9 inches. Trees are 5.0 inches and largerUrban FIA
SeedlingA stem under 1.0 inch in diameter and more than 0.5 foot long for conifers or more than 1.0 foot long for hardwoodsUrban FIA
ForkA stem that is at least one third the diameter of the main stem, leaves it at 45 degrees or less, and has or could assume an obvious tree-like form and functionUrban FIA
BoleThe main stem. It is the stem with the most merchantable volume, from one foot above the ground to the point where the diameter outside bark reaches 4 inchesUrban FIA
CullThe parts of a bole that are unusable for industrial wood products because of rot, form or other defectUrban FIA

Height and length words

Height and length terms
TermWhat the source recordsSource
Total lengthBole length from ground level to the tip of the apical meristem, to the nearest foot, on the uphill side on a slope. Tolerance is plus or minus 10 percentUrban FIA
Actual lengthGround to the break on a tree with a missing top. It stays the record until a new leader reaches one third the diameter of the broken topUrban FIA
Length methodA code for how lengths were found: measured with an instrument such as a clinometer, relascope or tape, partly estimated, or fully estimated by eyeUrban FIA
Total tree heightHeight from the ground to the top of the tree, alive or deadEco manual
Live tree heightHeight from the ground to the live top of the treeEco manual
Height to crown baseHeight from the ground to the base of the live crownEco manual

Crown words

Crown terms
TermWhat the source recordsSource
Crown topThe highest point of a standing tree. On many hardwoods it is a lateral branch, not the main terminalUrban FIA
Live crown baseAn imaginary horizontal line across the trunk at the bottom of the lowest live foliage of the obvious live crown, moved down when a live branch lies within 5 feet below it, on trees 5.0 inches DBH/DRC or largerUrban FIA
Uncompacted live crown ratioThe percentage of actual tree length that supports live foliage, found as live crown length over actual lengthUrban FIA
Compacted crown ratioThe share of tree length with live foliage after lower live branches are moved by eye into gaps in the upper crownUrban FIA
Crown widthThe live crown at its widest point, recorded to the nearest foot, with a second reading at right angles. Eco records width north-south and east-westUrban FIA, Eco manual
Crown classA five-way rating of a crown by sunlight received and nearness to neighbours: open grown, dominant, co-dominant, intermediate or overtoppedUrban FIA
Open grownA crown that got full light from above and from all sides through most of its life. Trees in clumps do not qualifyUrban FIA
Crown light exposureA count of crown quarters in full light, plus one if the top gets direct light. Eco counts the sides receiving sunlight from above, up to 5Urban FIA, Eco manual
Crown diebackRecent death of branches with fine twigs, from the tip toward the trunk, counted only in the upper and outer crownUrban FIA
Percent crown missingThe percent of the crown volume not occupied by branches and leavesEco manual
ConditionCrown condition recorded as 100 minus the percent of the crown made up of dead branchesEco manual
Live branchWoody lateral growth supporting foliage that is 1.0 inch or larger at the base above the swellingUrban FIA
Twig and sprigLateral growth under 1.0 inch at the base. A twig has secondary branching and a sprig does notUrban FIA
EpicormicShoots from latent or suppressed buds on old branches, the trunk or near large woundsUrban FIA
Snag branchA dead upper crown branch with no twigs or sprigs. A branch killed by shading is not oneUrban FIA
Overstory canopy zoneThe area between the average height of live crown bases and the average height of live crown tops of overstory treesUrban FIA

Cover and sampling words

Cover and sampling terms
TermWhat the source recordsSource
Percent tree coverThe share of a plot covered by tree canopy. In a plot-based Eco project it is a required field for each plotEco manual
Percent impervious under canopyThe percent of the area beneath the drip line of the tree that is imperviousEco manual
StratumA zone, such as a land use or neighbourhood, used to subdivide the study area. The manual says the number of strata is usually between 5 and 10 for an analysis with 200 total plots, cannot exceed 14, and calls for at least 20 plots in eachEco manual
Urban FIA plotA circular plot with a fixed radius of 48 feet, with smaller microplots for saplings and seedlingsForest Service program page
Cold check and blind checkQuality checks. A cold check inspects a finished production plot with the production data in hand. A blind check is a re-installation of the plot by a qualified crew without that dataUrban FIA

The British standard

The BSI catalogue lists BS 5837:2012, Trees in relation to design, demolition and construction. Recommendations, published April 30, 2012. It supersedes BS 5837:2005, which is withdrawn. The catalogue shows its status as current and under review. Its audience includes arboriculturists, architects, builders, landscape architects, land managers, contractors and statutory undertakers.

Sources