ArbNation Join free

Mobile stump grinders: HSE AFAG606, OSHA and Cal/OSHA wording and a California FACE case

HSE leaflet AFAG606 covers mobile stump grinders from PPE and debris curtains to start keys. OSHA 1910.212 and Cal/OSHA section 3428 word the guarding duty, and California FACE report 18CA002 records a rope caught in the wheel.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work.

HSE leaflet AFAG606

The Health and Safety Executive (HSE) leaflet AFAG606, Mobile stump grinders (rev1, 2013), covers safe working practices for mobile stump-grinding machinery. It is to be used with the manufacturer's handbook as part of a risk assessment. All operators must have had appropriate training in operating the machine and doing the tasks. The leaflet is guidance and not compulsory unless it says otherwise, and HSE adds that following it will normally be enough to comply with the law.

Personal protective equipment

  • A safety helmet to BS EN 397, if the risk assessment identifies one as required.
  • Hearing protection to BS EN 352 where noise exceeds 85 dB(A).
  • Eye protection: a mesh visor to BS EN 1731 or safety glasses to BS EN 166.
  • Protective boots with good grip and ankle support to BS EN ISO 20345.
  • Gloves with reinforced palms and fingers, and non-snag outer clothing.
  • A personal first-aid kit for each person, including a large wound dressing.

The machine

AFAG606 calls for guards on belts, shafts and fan blades, on both the machine and the power source. The debris curtains around the cutting head are to be present, intact and adequate. A power take-off shaft needs a guard to BS EN ISO 5674 along its full length. The machine needs an engine-stopping device that is marked, working and reachable from the normal working position, and a suitable fire extinguisher within reach.

The site

The leaflet lists warning and prohibition signs on all foreseeable approaches. Work stops if the safe working area is breached. Other points are a firm, level surface, the parking brake applied when the grinder is detached from the tow vehicle, and supplementary screening against flying debris. At the roadside the cutting head directs chips away from pedestrians and traffic.

For the cut itself, AFAG606 has the operator check for underground services and check the stump for stones and metal as far as reasonably practicable. Buttress roots are revealed by hand. The operator works from a point with a clear view of the cutting. Nobody approaches the cutting mechanism until it has come to a complete stop, and the start key is removed when the machine is unattended.

The leaflet also has cutters checked daily for damage and wear. A designated, responsible person knows the daily work programme, and operators can give emergency services enough detail to find them.

Guarding wording in US rules

OSHA 1910.212(a)(1) provides that one or more methods of machine guarding protect the operator and others in the machine area from hazards including rotating parts, ingoing nip points, flying chips and sparks. Guards are affixed to the machine where possible and must not themselves offer an accident hazard. The point of operation of machines whose operation exposes an employee to injury shall be guarded. The rule applies to machines in general and does not name stump grinders.

Cal/OSHA names them. Title 8 section 3428, Stump Cutters, filed February 27, 2018 and operative April 1, 2018, has two subsections. Stump cutters shall be equipped with enclosures or guards to protect employees. Each employee in the immediate area of stump grinding operations, the operator included, shall wear the PPE required by Article 10 of the General Industry Safety Orders.

Guarding and PPE wording by rule
RuleWording
HSE AFAG606Guards on belts, shafts and fan blades; debris curtains intact
OSHA 1910.212Guard the point of operation and rotating parts
Cal/OSHA 3428Stump cutters have enclosures or guards; PPE for everyone in the area

The workrest line on OSHA's tree care page

OSHA's tree care hazards page lists, among shop hazards, that workrests and tongue guards of grinders should be properly adjusted, citing 29 CFR 1910.215. That rule is titled Abrasive wheel machinery. Its workrest paragraph covers offhand grinding machines, where the work rests on a support set close to the wheel. It does not describe a stump grinder.

California FACE report 18CA002

OSHA's tree care page lists the California Fatality Assessment and Control Evaluation (FACE) report 18CA002, "A Laborer Dies When He is Pulled into a Tree Stump Grinder", under caught-in hazards. The California Department of Public Health's report dates the incident to April 9, 2018. A laborer was helping a landscaping company owner who ran the grinder. A rope tied around his waist was attached to an eye hook on the machine's disc guard. The rope caught in the grinding wheel and pulled him in. He died the next day.

The report records no written injury and illness prevention program and no formal stump grinder training for either man, only brief instructions from rental companies. The rental manager did not ask about the owner's knowledge of the machine, and the owner was not given the instruction manual. The manual warns against allowing additional workers within 75 feet while grinding.

The investigator recommended that landscaping companies train workers who operate stump grinders and see that they follow safety policies. The report also recommended that homeowners hire landscapers certified by organizations such as the Tree Care Industry Association or the International Society of Arboriculture.

Other stump grinder cases have a guide of their own, and the rules for chippers and stump grinders have another.

To correct or remove an entry, write to the address at the foot of this page.

Sources