Nominal and actual lumber sizes: PS 20-25 dressed sizes in inches and millimetres
Under PS 20-25 a dry nominal 2 by 4 is dressed to 1-1/2 by 3-1/2 inches, or 38.1 by 88.9 mm. The nominal size is a label and is larger than the dressed size.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The American Softwood Lumber Standard, Voluntary Product Standard PS 20-25, dated January 2025, supersedes PS 20-20 Revision 1. The American Lumber Standard Committee (ALSC) maintains it, and the National Institute of Standards and Technology (NIST) publishes it. In PS 20-25 the values in inches are the units of record, and the millimetre values are given only for information and comparison.
What nominal means
PS 20-25 defines nominal size as the label designation for lumber size categories that does not reflect the dressed size. It says no inference is to be drawn that nominal sizes are dressed sizes. The standard sorts lumber by nominal thickness:
- Boards are under nominal 2 inches thick.
- Dimension runs from nominal 2 inches up to, but not including, nominal 5 inches.
- Timbers are nominal 5 inches or more in least dimension.
Dry lumber under nominal 5 inches thick is seasoned or dried to a maximum moisture content of 19 percent. The Forest Products Laboratory Wood Handbook says lumber length is recorded in actual dimensions, while width and thickness are recorded in nominal ones. It also says softwood lumber comes in length multiples of 305 mm (1 ft).
Dimension lumber thicknesses
| Nominal | Minimum dressed, dry | Minimum dressed, green |
|---|---|---|
| 2 in | 1-1/2 in, 38.1 mm | 1-9/16 in, 39.7 mm |
| 2-1/2 in | 2 in, 50.8 mm | 2-1/16 in, 52.4 mm |
| 3 in | 2-1/2 in, 63.5 mm | 2-9/16 in, 65.1 mm |
| 3-1/2 in | 3 in, 76.2 mm | 3-1/16 in, 77.8 mm |
| 4 in | 3-1/2 in, 88.9 mm | 3-9/16 in, 90.5 mm |
| 4-1/2 in | 4 in, 101.6 mm | 4-1/16 in, 103.2 mm |
Dimension lumber widths
| Nominal | Minimum dressed, dry | Minimum dressed, green |
|---|---|---|
| 2 in | 1-1/2 in, 38.1 mm | 1-9/16 in, 39.7 mm |
| 3 in | 2-1/2 in, 63.5 mm | 2-9/16 in, 65.1 mm |
| 4 in | 3-1/2 in, 88.9 mm | 3-9/16 in, 90.5 mm |
| 5 in | 4-1/2 in, 114.3 mm | 4-5/8 in, 117.5 mm |
| 6 in | 5-1/2 in, 139.7 mm | 5-5/8 in, 142.9 mm |
| 8 in | 7-1/4 in, 184.2 mm | 7-1/2 in, 190.5 mm |
| 10 in | 9-1/4 in, 235.0 mm | 9-1/2 in, 241.3 mm |
| 12 in | 11-1/4 in, 285.8 mm | 11-1/2 in, 292.1 mm |
| 14 in | 13-1/4 in, 336.6 mm | 13-1/2 in, 342.9 mm |
| 16 in | 15-1/4 in, 387.4 mm | 15-1/2 in, 393.7 mm |
Boards and timbers
Table 3 gives boards widths from nominal 2 to 16 inches, with odd widths of 7, 9 and 11 inches that dimension lumber lacks. The dressed values for the widths they share are the same as above. Dimension lumber is also listed at nominal 2-1/2, 3-1/2 and 4-1/2 inches wide, with the dressed values in the thickness table. Board thicknesses run from nominal 3/8 inch, dressed dry to 5/16 inch, up to nominal 1-1/2 inches, dressed dry to 1-1/4 inches (31.8 mm). A nominal 1 inch board is 3/4 inch (19.1 mm) dry and 25/32 inch (19.8 mm) green.
Timbers are listed as an amount taken off the nominal size rather than a fixed number. Dry dressed timbers of nominal 5 and 6 inches are 1/2 inch (12.7 mm) off, 7 to 15 inches are 3/4 inch (19.1 mm) off, and 16 inches and over are 1 inch (25.4 mm) off. Green timbers are 1/2 inch off at every size.
The Wood Handbook says the green and dry sizes are matched so that a piece surfaced to the standard green size shrinks to about the standard dry size at about 15 percent moisture content. The Wood Handbook also defines dry boards and dimension as lumber dried to a maximum moisture content of 19 percent, the limit PS 20-25 sets.
UK and metric sizes
BS EN 336:2013, titled Structural timber, sizes, permitted deviations, is the European standard BSI lists as current for this subject. Its scope sets two classes of permitted deviation from target sizes for softwood and hardwood structural timber. It also sets the moisture content used as the reference for measuring size and gives average size changes for moisture change. It applies to sawn and prepared square-edged timber with parallel edges and sawn thicknesses or widths over 6 mm. BSI prints no target sizes in the scope. PS 20-25 gives millimetre values for information and comparison only.
Sources
- NIST and ALSC, Voluntary Product Standard PS 20-25, American Softwood Lumber Standard, January 2025, read October 16, 2026
- ALSC, Lumber additional documents PS 20, current edition PS 20-25, read October 16, 2026
- USDA Forest Products Laboratory, Wood Handbook FPL-GTR-282, March 2021, chapter 6 commercial lumber, read October 16, 2026
- BSI Knowledge, BS EN 336:2013 Structural timber, sizes, permitted deviations, scope, read October 16, 2026