ArbNation Join free

Outriggers, pads and ground bearing for lifts and cranes: OSHA, WorkSafeBC, HSE

OSHA 1926.1402 requires firm, drained, graded ground for cranes. WorkSafeBC 14.67 to 14.69 covers outrigger floats and supporting surfaces, and HSE's LOLER code lists the ground factors behind overturning.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. It is not training and does not teach the work.

United States: 29 CFR 1926.1402, ground conditions

Section 1926.1402 defines ground conditions as the ability of the ground to support the equipment, including slope, compaction and firmness. Supporting materials are blocking, mats, cribbing, marsh buggies in marshes or wetlands, and similar devices. The section does not use the word outrigger.

ParagraphWhat it says
(b)The equipment is not to be assembled or used unless the ground is firm, drained and graded enough that, with supporting materials where needed, the manufacturer's specifications for support and level are met. Drainage does not apply to marshes and wetlands
(c)The controlling entity provides the ground preparations. It also tells the user and operator where it knows of hazards under the set-up area, such as voids, tanks and utilities, if site drawings, as-built drawings or soil analyses in its possession show them
(d)With no controlling entity on the project, the employer with authority over ground preparations carries the duty in (c)(1)
(e)If the A/D director or the operator finds the ground falls short, that person's employer holds a discussion with the controlling entity about the preparations needed
(f)The section does not apply to cranes built for railroad tracks, when used on the general railroad system

British Columbia: OHS Regulation Part 14

Part 14 covers cranes and hoists. Sections 14.67 to 14.69 apply to a mobile crane or boom truck. Section 14.69 was enacted by B.C. Reg. 320/2007, effective February 1, 2008, and 14.67 was amended by B.C. Reg. 312/2003 and 320/2007.

  • Section 14.67(2): outrigger beams and stabilizers must be marked to show when the necessary extension has been reached.
  • Section 14.67(4): floats must be secured to the outrigger jacks when outriggers are used.
  • Section 14.69(1): the machine must be used only on a surface able to support it safely, with any hoisted load.
  • Section 14.69(2): next to an excavation, slope or backfilled area, a qualified person must decide where the machine stands for hoisting.
  • Section 14.69(4): blocking, shoring or cribbing must be sized and used as needed so the load from the support does not exceed the bearing capacity of the surface.

Section 14.68 adds that tire type, condition and inflation must be as the manufacturer specifies when lifting on rubber.

United Kingdom: HSE L113 on lifting equipment

L113 is the approved code of practice and guidance on the Lifting Operations and Lifting Equipment Regulations 1998, second edition 2014 with amendments in 2018. Paragraphs 99 to 103 deal with stability. Where safe use depends on stabilising arrangements, the equipment should not be used unless they are in place and working. The guidance names these factors in paragraph 102.

Factor affecting stabilityL113 wording
Strength of the groundSpreader plates may be needed so the surface can support the weight of the equipment and the maximum load
Stability under loadToo close to an excavation, the ground may slowly subside or collapse suddenly
SlopeA slope adds horizontal forces on top of vertical ones
The loadIts size, its nature, how it is lifted and the maximum wind loading

Ways to improve stability, listed in paragraph 103, are a suitable base, an anchorage system, counterbalancing weights, and ballast, outriggers, stability arms or stabilisers. Under paragraph 257 there should be enough space to put out any outriggers, and access routes should be strong enough for the loads from mobile lifting equipment. Equipment should not be used in a manner likely to cause it to overturn (paragraph 258).

HSE on MEWP ground and outriggers

HSE records that operators have died when a MEWP overturned. Its MEWP guidance calls for firm and level ground, with temporary covers strong enough for the applied pressure. Trenches, manholes and uncompacted backfill can all lead to overturning. Outriggers must be extended and chocked before the platform is raised. Spreader plates may be needed, and the equipment manual is the place to check.

L113 is published under the Open Government Licence v3.0, Crown copyright.

Sources