Planting hole size and shape: what extension and specs state about width and depth
Iowa State, Delaware and Utah State put hole width at 2 to 3 times the root ball. The sources differ on depth, from 2 or 3 inches shallower than the ball to the exact height of the ball.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
Extension services and city specs publish rules for planting hole width, depth and shape, described below. It is not training and does not teach the work.
Width
Iowa State University Extension gives a hole 2 to 3 times wider than the diameter of the root ball, for balled and burlapped and container trees in well-drained soil. The University of Delaware lists "dig a hole 2-3 times the width of the root ball" among its do's and "dig the hole just wide enough to fit the root ball" among its don'ts.
Utah State University Extension calls for a hole "much wider than the root ball" with sloping sides, and at least 2 to 3 times the root ball width. The reason it gives: most tree roots grow horizontally and stay fairly shallow.
Clemson's shrub factsheet gives a wider band, two to five times the root ball, on the grounds that wider holes let roots establish faster. The City of Peterborough, Ontario, sets a floor in its December 2024 planting spec: not less than twice the root ball diameter, measured at the top of the ball.
Depth
| Source | Depth of the hole |
|---|---|
| Iowa State University Extension, well-drained soil | 2 or 3 inches less than the height of the root ball |
| Iowa State University Extension, poorly drained soil | About two-thirds of the height of the root ball, with the top one-third above the surrounding soil |
| University of Delaware | Not deeper than the root ball; the trunk flare is visible when the tree sits in the hole |
| Utah State University Extension | Just deep enough that the bottom of the ball rests on undisturbed soil and the root collar is at or above the surrounding soil |
| Clemson, shrub factsheet | Never deeper than the height from the uppermost roots to the bottom of the root ball |
| City of Peterborough, Ontario | The distance from the trunk flare to the bottom of the root ball |
Utah State and Clemson both leave the soil at the bottom undisturbed. Utah State gives the reason: loosened soil lets a heavy root ball settle and sink, so the tree ends up too deep.
Shape of the sides
Iowa State describes a sloped hole: the top is several inches wider than the bottom. Utah State also calls for sloping sides. It adds that sides can become glazed and smooth during digging, and that growing root tips may not get through a glazed surface. Its text names picking at the soil with the tip of a spade as the way to rough them up.
Clemson's shrub sheet describes the same glazing in heavy clay, "similar to the inside of a terra cotta pot", and names notching the sides with a shovel or mattock.
Root ball size
Utah State gives a size check for the stock itself: 10 to 12 inches of root ball, container diameter or root spread for every inch of stem caliper. A 3 inch caliper tree comes to a root ball at least 30 to 36 inches wide. It rates root ball depth as less critical than width.
Poorly drained sites
Iowa State changes only the depth for poorly drained soil. Width stays at 2 to 3 times the ball, depth drops to about two-thirds of the ball, and the backfill is placed to the top of the ball and sloped down to the surrounding soil.
Sources
- Iowa State University Extension, How large of a hole should be dug when planting a tree, updated December 3, 2024, read October 16, 2026
- University of Delaware Cooperative Extension, Plant Installation, updated March 2025, read October 16, 2026
- Utah State University Extension, Planting Landscape Trees, read October 16, 2026
- Clemson Home and Garden Information Center, Planting Shrubs Correctly, read October 16, 2026
- City of Peterborough, Tree Planting: Installation and Establishment, specifications CP 801.01 and others, December 2024, read October 16, 2026