Prusik hitch: what the codes, test papers and makers record about it
The NSW tree works code gives Prusik loops their own item, the UK industry code defines friction hitches, and a UK report and an Italian paper pulled Prusik hitches on test benches.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
What the named codes, test authors and makers publish about the Prusik hitch is described here. It is not training and does not teach the work.
The NSW code on Prusik loops
SafeWork NSW's Tree works code of practice, in force since 27 March 2026, gives Prusik loops their own item, 4.7. Its glossary defines a Prusik loop as a loop of rope smaller in diameter than the climbing rope, attached to the climbing rope with a prusik knot and used to attach the climber to the climbing rope.
The code lists five points for Prusik loops and other friction knots. The first three cover compatibility with the climbing rope, fit for purpose rope, and a length that suits the climber and the system. The last two cover testing at ground level before first use in a tree, and inspection before and after each use for heat and abrasion damage.
The UK industry code on friction hitches
The Industry Code of Practice for Arboriculture: Tree Work at Height, second edition, May 2020, uses the wider word hitch. Its glossary calls a friction hitch any of several knots and hitches that control ascent, descent or position on the rope and self lock when released.
Clause 3.10.6.8 sets two criteria for any friction hitch cord. The cord must suit its use, judged by diameter and construction, from materials resistant to the abrasion and temperatures met in work and rescue. The way it is attached to a connector or placed in a system must not stop the hitch locking positively and reliably when advanced or during descent.
The Treevolution report
Paolo Bavaresco of Treevolution tested ropes and friction hitches under a contract awarded in March 2002. His report spells Prusik with a capital P for the traditional hitch and with a small p for every hitch tied by winding cord around a rope. It calls the prusik the hitch UK tree climbers had used for at least half a century in a doubled rope system.
The tests covered a 4-wrap and a 6-wrap Prusik among eight named hitches. In the single rope pull test, the 6-wrap Prusik had the lowest failure rating of the setups that tested satisfactorily, a safety factor just under 19:1 after strength reduction from knots. The lifeline bowline was the failure point. In the doubled rope pull test, the highest result was for a 7-wrap Valdotain tresse.
The report's recommendations list the 4-wrap and 6-wrap Prusik with a 10 mm cord, and with a 13 mm cord, on a 13 mm work line. It adds that cords of 6 mm cannot be recommended for friction hitches in arboriculture.
The Tuscia paper
Bianchini and five co-authors at the University of Tuscia published "Tensile Strength of Ropes and Friction Hitch Used in Tree Climbing Work" in Forests on 26 October 2021. They ran 36 tests on two rope models and two hitches, the Prusik and the Valdotain tresse. Each treatment had nine replicas.
| Item and maker | Material, diameter | Declared load |
|---|---|---|
| Axis rope, Petzl | Polyester, polyamide, 11 mm | 22 kN |
| XTC 16 rope, Yale Cordage | Polyamide, 13 mm | 24 kN |
| Timber prusik cord, Tendon | Polyester, technora, 8 mm | 22 kN |
The Prusik reached higher loads than the tresse. The maximum load averaged 11.9 kN on the 11 mm rope and 15.1 kN on the 13 mm rope with the Prusik, against 9.3 kN and 8.6 kN with the tresse. The paper reports lower slip with the Prusik, and a larger reduction in rope diameter. The highest load in the 36 tests was 18.7 kN.
The paper cites earlier authors who put the first sign of failure in Prusik knots between about 4 and 6 kN. The paper's own tests partly repeat that, with first signs of failure from 4 kN on the 11 mm rope to 10 kN on the 13 mm rope. In T. Evans's Prusik breaking tests, which the paper also cites, the knot is influenced by the diameter of the rope it is tied to.
Sources
- SafeWork NSW, Tree works code of practice, March 2026, section 4.7 and glossary, read October 21, 2026
- Arboricultural Association and partners, ICoP for Arboriculture: Tree Work at Height, Edition 2, May 2020, glossary and clause 3.10.6.8, read October 21, 2026
- Paolo Bavaresco, Treevolution, Ropes and Friction Hitches used in Tree Climbing Operations (contract March 2002), copy hosted by Treetools, read October 21, 2026
- Bianchini and others, University of Tuscia, Forests 2021, 12, 1457, published October 26, 2021, read October 21, 2026