Pulling trees with a rope, truck or tractor: what the codes say
Four regulators address pulling a tree over or away from its fall line. New Zealand's code allows a pull toward a machine if two tree-lengths of clearance exist; OSHA exempts tree pulling from two of its felling rules.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work.
The codes side by side
| Source | Wording on pulling, anchors and distance |
|---|---|
| HSE, winches in directional felling | Covers a tractor winch or hand winch as an aid to directional felling and assisted takedown. It does not apply to timber extraction or to towing vehicles or other equipment. The chainsaw operator is in control and gives instructions to the machine operator. |
| HSE, machine-assisted takedown | Many incidents have occurred where operators use machines to assist in the takedown of large edge trees and hung-up or leaning trees. |
| WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012 | A pulling line should be attached to all trees and stems being felled where assisted directional felling is required. For felling against the lean (back-pulling), the rope should be secured as high as practicable. If two tree-lengths of clearance is possible, the tree may be pulled toward the machine or point of equipment anchor. |
| SafeWork NSW, Tree works code of practice, commenced March 27, 2026 | Controlled directional felling uses pulling or pushing methods. Anchor points for ropes or cables are capable of holding the total load. Vehicles or mobile plant used as anchors are kept outside the drop zone. Pushing operations use suitable mobile plant only. |
| OSHA, 29 CFR 1910.266 logging operations | No yarding machine operates within two tree lengths of trees being manually felled, except yarding machines doing tree pulling. The rule that the backcut sits above the horizontal facecut carries an exception: the backcut may be at or below it in tree pulling operations. |
Communication between the saw and the machine
HSE lists the agreements made before work starts. An emergency stop signal must immediately be obeyed by everyone, and any unclear signal is treated as a stop signal. If the chainsaw operator cannot see the machine operator, a radio or a third person to relay the message is used.
WorkSafe New Zealand puts the same duty on the faller. Before felling begins, the faller advises winch and machine operators on line tension and on winching and pulling speeds. Visual signals and vocal commands are set before felling starts. For back-pulling, the faller and the machine operator have an effective means of communication, which may need an intermediary. Everyone doing the pull is competent or training under adequate supervision.
Distance and exclusion zone wording
The New Zealand code keeps people not directly helping with the felling at least two tree-lengths from the tree. No machine works within two tree-lengths of a felling in progress, unless it is helping, under adequate supervision, to bring the tree to the ground.
In New South Wales the code ties the technique to space. Controlled directional felling is used where space is limited, with less than two tree lengths, or where the natural fall would meet overhead lines, structures or hung trees. Ground workers are told never to stand in the direct line of a tensioned winch cable or tow-rope, and the code sets the working load limit to be determined and observed before winching.
OSHA's two tree lengths, in the logging standard, apply between a felling and an occupied work area or yarding machine. Tree pulling is not defined in the standard's definitions list. The standard does define a spring pole as a tree, segment, limb or sapling under stress or tension from the pressure or weight of another object. When one is cut, no employee other than the feller is closer than two tree lengths.
Anchors, ropes and line pull
The New South Wales code ties rope numbers to the drop zone: arcs of 180 to 90 degrees call for at least two ropes. Ropes are set high in the tree to control the fall direction, and tree defects such as multiple trunks are considered when anchors are chosen. Ropes, cables and winches are rated appropriately for the expected loads.
The New Zealand code gives figures. When a stump is the ground anchor or secures pulling blocks, it is of sufficient size and stability for the winching operation. Strops anchoring winches or pulling blocks are at least 1.5 times the safe working load (SWL) of the pulling rope. Line pull does not exceed the SWL of the rope or its accessories, and for all arboricultural operations the SWL is one-sixth of the breaking strength. No person remains in the bight of a working rope, and knots in wire rope are prohibited.
Where the sources differ
- HSE's winch page excludes towing vehicles or other equipment from its scope. The New Zealand and New South Wales codes both mention machines or mobile plant as the anchor or the pulling force.
- OSHA exempts yarding machines doing tree pulling from the two tree length rule. New Zealand allows pulling toward the machine only with two tree-lengths of clearance.
- HSE prints no distance on either page. The New Zealand and OSHA texts print two tree lengths.
Related pages are felling distances and danger zones and winches and pulling devices.
Sources
- HSE, Winches in directional felling, page dated August 26, 2026, read October 19, 2026
- HSE, Machine-assisted takedown, page dated August 26, 2026, read October 19, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 19, 2026
- SafeWork NSW, Tree works code of practice, commenced March 27, 2026, read October 19, 2026
- OSHA, 29 CFR 1910.266 Logging operations (eCFR), read October 19, 2026