Rigging from the tree or from the ground: how the ISA rigging book and the codes divide anchor and lowering points
The UK Industry Code of Practice defines an anchor as a place a line attaches and describes a lowering device as a tube or bollard that creates friction. California's Title 8 section 3427 separates ropes for lowering limbs from climbing lines.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work.
The terms each source uses
| Source | Term and wording |
|---|---|
| Industry Code of Practice, Edition 2, May 2020 | Anchor: a structural place, fixing or fixture to which a safety line or anchorage device is attached. Anchor point: a point of attachment for personal fall protection systems or anchor devices. Rigging: the process by which trees or parts of trees are removed in sections, controlled using ropes, pulleys and friction devices. |
| Industry Code, lowering devices | Based on the design principle of a tube or bollard around which the rope is wound to create friction or a deviation. They range from simple tubular components to modular systems with a winching function. |
| Industry Code, pulleys, blocks and trolleys | Can create deviations in a rope, reduce friction, generate mechanical advantage or allow lateral movement. Sheave efficiency is to be commensurate with the application. |
| Arboricultural Association Safety Guide 3, December 2021 | Separate checklist headings for anchor forces, operator positioning, anchor selection and peak loads. Rigging techniques are checked for enough competent operators, both aerial and ground based. |
| California Title 8, section 3427 | Tie-in point, rigging system, lowering devices and lowering ropes are dealt with in separate paragraphs. |
The attachment point and the lowering device in the UK documents
The Industry Code lists duties for operators in rigging: identify drop zones, estimate log and crown section mass, calculate expected peak forces and select compatible components. It requires lowering devices to be rated for the anticipated loads, including dynamic loading during rigging. They must suit the technique, whether lowering, lifting or both, and be compatible with neighbouring components, particularly rope diameter against tube or bollard diameter. They must also be configured so they do not slip excessively.
Safety Guide 3, a checklist summarised from the Association's Technical Guide 3, asks whether the system is set up to minimise anchor forces, whether friction is managed and whether redirects reduce anchor force. Its anchor selection section asks if the anchor is strong enough, if the consequences of anchor failure were considered, and if PPE and rigging anchors are suitably independent. The guide also states that a decision must be made on whether it is necessary to climb, or whether work may be carried out from the ground or a platform, with reference to the Industry Code.
Ground level in the Industry Code
The Industry Code says work at height should not take place when it is reasonably practicable to do the work from the ground. That passage concerns whether to go aloft at all. It is not a rule about where a lowering device sits. None of the three documents sets out a rule choosing between a rigging point in the tree and a friction point at the base.
California section 3427
California, in the Tree Work, Maintenance or Removal article, gives the employer's duties in paragraphs. When a rigging system is necessary, a qualified tree worker determines the appropriate system based on factors including species, size, weight and length of the tree sections or limbs. Wedges, block and tackle, rope and other lowering devices are used when a removed tree may fall in the wrong direction or damage property.
Separate ropes for lowering limbs are attached to limbs that cannot be dropped or are too heavy to be controlled by hand. Climbing lines are not attached to the same crotch as ropes used for lowering limbs. Only qualified tree workers directly involved in the operation are permitted in the drop zone while a load is suspended by a rigging system. The tie-in point for climbing is set on or around the main leader or a major upright branch, using branches with a wide crotch, as near as possible over the work area.
The ISA rigging title
The ISA store lists The Art and Science of Practical Rigging as a DVD and workbook set. The Industry Code's reference list also names a 2001 ISA title of the same name. The store page carries no text from the work.
Related pages are rigging gear by type and rigging words.
Sources
- Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, hosted by the Arboricultural Association, read October 19, 2026
- Arboricultural Association, Safety Guide 3: Rigging and Dismantling, December 2021, read October 19, 2026
- California Department of Industrial Relations, Code of Regulations Title 8, section 3427 Safe Work Procedures, read October 19, 2026
- International Society of Arboriculture, webstore, Climbing and Rigging listing, read October 19, 2026