ArbNation Join free

Rigging knots and hitches in three Australian training units: AHCARB213, 311 and 319

Three Australian training units name the rigging and climbing knots a learner must show: 14 for ground-based rigging, 11 for above-ground work and 19 for climbing. SafeWork NSW and WorkSafe NZ list none by name.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

The text below describes what the named codes and training bodies publish. It is not training and does not teach the work.

Three units, one publisher family

All three units come from the AHC training package of the Commonwealth of Australia, so they are one source family and not three independent codes. The 2022 unit carries a Skills Impact footer and the 2025 units a Skills Insight footer. AHCARB213 Perform ground-based rigging is a unit whose assessment requirements the Commonwealth generated on 11 February 2025. The AHCARB311 unit Tie, dress, set and finish arborist knots was generated on 1 August 2022. The AHCARB319 Use arborist climbing techniques assessment requirements were generated on 11 February 2025.

AHCARB213 asks for evidence that the person installed rigging equipment and controlled at least six loads from an aerial location to the drop zone, using ropes, knots and a rigging system suited to the load. The knots are tied, dressed, set and finished according to the rigging task. AHCARB311 describes the knots, hitches and bends for ground-based workers. It weighs each knot for locking and non-locking attributes, strength, effect on rope strength, loosening and slippage. AHCARB319 requires 19 climbing knots and hitches for rigging and climbing, plus at least one advanced climbing hitch.

Names by unit

Yes means the unit names the knot and No means it does not. The table follows the spelling of each unit, grouped where two lists use different words for one knot. AHCARB311 prints three lists: ground-based rigging, above-ground applications and aerial rigging. The ground-based list in AHCARB311 matches the list in AHCARB213 knot for knot.

Rigging lists

Name as printedGround (213, 311)Aerial (311)
Alpine butterfly knotYesYes
Bowline on the bightYesYes
Cow hitch with better half (aerial list: cow hitch)YesYes
Clove hitch and two half hitchesYesYes
Half hitch pre-knotYesYes
Klemheist friction knotYesNo
Marline pre-knotYesYes
Marline spike hitchYesYes
Riggers knot and two half hitchesYesYes
Running bowlineYesYes
Sheet bendYesYes
Slippery sheet bendYesYes
Timber hitchYesYes
Zeppelin bendYesYes
Rolling hitchNoYes

Above-ground and climbing lists

Name as printedAbove ground (311)Climbing (319)
Alpine butterfly knotNoYes
Bowline on the bightNoYes
Klemheist friction knotNoYes
Marline spike hitchYesYes
Running bowlineYesYes
Sheet bendYesYes
Slippery sheet bendYesYes
Zeppelin bendNoYes
Clove hitchYesYes
Scaffold knotYesYes
Double fisherman's knot or bend, prusik loopYesYes
Girth hitchYesYes
Prusik hitch (English prusik)YesYes
Double overhand stopper knotYesYes
Bowline knotYesYes
Blake's hitchNoYes
Figure-8 loopNoYes
Munter hitchNoYes
Flemish bendNoYes

AHCARB319 also names four advanced climbing hitches and asks for at least one: Distel hitch, Valdôtain tresse (French prusik), Schwabisch hitch and Knut. The unit lists the friction hitches Blake's hitch and the prusik hitch, with limits, advantages and disadvantages, in its knowledge evidence.

Codes that do not list the names

SafeWork NSW's Tree works code of practice of March 2026 does not name any of these rigging knots. It names prusik loops, and its fall prevention controls say not to use knots that are insecure if tied incorrectly, need a second knot for security, or creep or loosen under load. WorkSafe New Zealand's Approved Code of Practice for Safety and Health in Arboriculture, November 2012, has a section on knots in arboricultural operations. It asks that anyone tying knots be competent and fully trained in them, and it repeats the sequence tie, dress, set. It lists no rigging knot names.

Other knot names used in tree work sit in the guide to the knots arborists use, and rope losses from knots in the guide to knot strength loss.

Sources