ArbNation Join free

Setting up a bucket truck or MEWP: outriggers, pads and slopes in four regulators' texts

OSHA's rule puts outriggers on pads or a solid surface and calls for wheel chocks on an incline. HSE, the HSA and WorkSafe NZ add ground checks, spreader plates and slope limits.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

Four regulators print wording on where a bucket truck or other mobile lift (a MEWP) stands. They are OSHA in the United States, the Health and Safety Executive (HSE) in Britain, the Health and Safety Authority (HSA) in Ireland and WorkSafe New Zealand. The named codes and training bodies are described here as published. It is not training and does not teach the work.

United States

OSHA publication 3940, Solutions for Tree Care Hazards (2018), has an aerial lifts column. Three of its points concern set-up, in the sheet's own words:

  • Set outriggers on pads or on a level, solid surface.
  • Set brakes when outriggers are used.
  • Use wheel chocks on sloped surfaces.

The sheet names falls, electrocutions and equipment collapses or tip-overs as the major causes of injuries and deaths with aerial lifts. It also lists following the manufacturer's instructions.

The rule behind it is 29 CFR 1926.453(b)(2)(vii), for extensible and articulating boom platforms. Brakes are to be set. Outriggers, when used, are to be positioned on pads or a solid surface. Wheel chocks are to be installed before the lift is used on an incline, provided they can be safely installed. Paragraph (b)(2)(xii) adds that before travel the boom is to be cradled and the outriggers stowed. Paragraph (b)(2)(vi) bars exceeding the boom and basket load limits the manufacturer specifies.

United Kingdom

HSE General Information Sheet GEIS6, first published in October 2014, covers vehicle-mounted booms along with scissor lifts, self-propelled booms and trailer-mounted booms. It frames set-up as a list of questions for the planner:

  • Is the ground sufficiently level at the work location?
  • What is the ground bearing capacity at the work position and along the route to and from it?
  • Is there enough space for the outriggers to be deployed?
  • What is the maximum point load under a wheel, outrigger or jack pad, and are spreader plates required?

GEIS6 also says the person in control of the site should supply the ground bearing capacity, terrain, gradient and base area. Trenches, manholes and uncompacted backfill are named as local features that could lead to overturning. A MEWP parked on a gradient should have its wheels chocked.

Ireland

The HSA's 2017 guidance on MEWPs says the ground under a MEWP should be examined before it is operated. The ground should be level, stable and unable to compress under the machine. A risk assessment by people with the right knowledge and expertise should establish whether a visual inspection will suffice or a full geotechnical survey is also required. After heavy rain, flooding or freezing of the ground, reassessment checks may be needed, because the MEWP could sink.

Where outriggers are in use, the HSA calls suitable spreader pads or plates necessary for stability. Its further points on pads:

  • The outrigger foot is to be centred on the pad, and any hollow filled first.
  • Very poor ground may need timber mats, proprietary mats, steel grillages or concrete pads.
  • Timbers must be of adequate strength, thickness and condition, and scaffold boards are never to be used.
  • MEWPs are not to stand close to trenches, excavations or spoil, and cracking over a backfilled trench is a warning sign.

Paved areas can look strong but may be laid on weak ground, the HSA adds, and underground services such as sewers, drains and mains can make a MEWP unstable. A MEWP parked on a gradient should have its wheels chocked.

New Zealand

WorkSafe NZ's guidelines for MEWPs, last updated October 10, 2017, have separate paragraphs on ground conditions and outriggers. The guidelines use "must" for a legal requirement and "should" for recommended practice. On ground, they put the MEWP on firm, level ground where possible, rated for any slope it meets, and warn that trenches, manholes and soft ground can make it overturn. Temporary covers over holes are to be strong enough for the whole weight of the machine at its maximum rated capacity.

On outriggers, WorkSafe NZ says to set them before raising the platform, using the maker's instructions. Spreader plates are used when the ground calls for them, in a material that grips both the foot and the ground. On a ramp, extreme caution is needed to stop the machine slipping down it, and outrigger footplates are not to be set up on a slope. The guidelines also list interlocking outriggers among the guarding a MEWP must have, so the platform cannot lift unless they are in a safe position.

Slopes in the four texts

What each text prints about slopes and inclines
RegulatorWording on slopes
OSHAWheel chocks before use on an incline, provided they can be safely installed
HSEGround sufficiently level at the work location is a planning question; chocked wheels when parked on a gradient
HSALevel ground surfaces; chocked wheels when parked on a gradient
WorkSafe NZMEWP rated for any slope it faces; no use beyond the inclinometer or maker's limit; outrigger footplates not set up on a slope

OSHA's incline wording and WorkSafe NZ's slope wording differ: OSHA speaks of chocks on an incline, while WorkSafe NZ bars footplates on a slope. Each is printed as its regulator has it.

Sources