Chainsaw sprockets: rim and spur types and the wear limits makers print
Makers' manuals treat the chain sprocket as a wear part. Two print a 0.5 mm wear limit, two print a replacement interval of two chains, and one leaves the call to a dealer.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named makers' manuals and an HSE leaflet are described here as published. It is not training and does not teach the work. Each saw's own manual sets the detail for that saw.
The sprocket as part of the cutting attachment
One maker's manual for a professional saw defines the cutting attachment as the saw chain, the guide bar and the chain sprocket. In that manual the chain, bar and sprocket must match each other and the saw, and all three are changed in due time.
A chain maker's maintenance manual calls chain, bar and sprocket a team that must be maintained as a team. Its contents list a section on drive sprockets, with rim sprockets that carry wear-depth indicators. Chain pitch is the link to the other two parts. For pitch and gauge figures, see chain pitch, gauge and file size by maker.
Rim sprocket, spur sprocket and bar-nose sprocket
Two drive types appear in the manuals. A rim sprocket sits on the clutch drum and can be replaced alone. A spur sprocket is the other drive type: the STIHL replacement section lists it as an alternative to the clutch drum on the crankshaft and covers both types together.
A third sprocket sits at the tip of some guide bars. The same maker lists its sprocket-nose bars by tooth count: 10 and 11 teeth on the bars in its data section. The pitch of the chain, the drive sprocket and the nose sprocket must match.
Husqvarna makes the same point: the distance between the drive links of the chain must line up with the teeth on the bar-tip sprocket and the drive sprocket. It lists the number of teeth on the bar-tip sprocket among the details to match when a bar is chosen.
Wear limits and replacement intervals as the manuals print them
| Publisher and saw | Sprocket type named | Wear or interval statement |
|---|---|---|
| STIHL MS 261 C-M instruction manual | Rim sprocket or spur sprocket; 7-tooth for .325 in. chain | Replace after two saw chains or earlier, or if the wear marks are deeper than 0.5 mm. A check gauge is a special accessory. Two chains used in alternation help preserve the sprocket |
| ECHO CS-590 chain saw instruction manual | Sprocket on the clutch | Replace when worn out 0.5 mm (0.02 in.) or more. Check when a new chain is installed |
| Oregon chain, bar and sprocket maintenance manual | Drive sprocket | Check daily. Replace drive sprocket systems after every two chains, or sooner |
| Husqvarna 545 Mark II and 550XP Mark II operator's manual | Rim sprocket on the clutch drum | Listed in the daily maintenance column. No figure given: if worn, speak to a servicing dealer |
| HSE leaflet AFAG308, top-handled chainsaws | Drive sprocket | Check periodically for excessive wear or damage |
What the makers tie to a worn sprocket
ECHO links a damaged sprocket to premature damage or wear of the saw chain. Oregon rules out running any chain on an overworn drive sprocket, a new chain most of all. Its sharpening section lists wear patterns on the chain that may point to a worn bar or sprocket.
Husqvarna links wrong chain tension to more wear on the guide bar, the chain and the chain drive sprocket, and poor lubrication to the same. STIHL puts the cost of a worn sprocket on the chain: past the wear marks, the service life of the saw chain is reduced.
Where the makers differ
STIHL and ECHO both print 0.5 mm as the wear depth. STIHL ties it to wear marks on the sprocket and adds an interval of two chains. ECHO gives the depth alone. Oregon prints the interval but no depth in the pages that open. Husqvarna prints neither and sends the owner to a dealer. Each figure belongs to that maker's own sprockets.
Who calls for sprocket checks
The HSE leaflet on top-handled chainsaws includes the drive sprocket in a maintenance checklist next to guide bar rails, chain wear patterns and anti-vibration rubbers. The leaflet has maintenance carried out as the manufacturer's handbook specifies. The Husqvarna schedule puts the sprocket check in its daily column. The ECHO manual ties the check to fitting a new chain.
STIHL also recommends its original chain sprockets so the chain brake works as intended. Regulators put the brake itself on the pre-use list: chainsaw checks before and during use carries it.
Sources
- STIHL, MS 261 C-M instruction manual, 0458-153-8321-C, read October 19, 2026
- Husqvarna, 545 Mark II, 545G Mark II, 550XP Mark II and 550XPG Mark II operator's manual, 544-013 of November 19, 2024, read October 19, 2026
- ECHO, CS-590 chain saw instruction manual, 2015 print, read October 19, 2026
- Oregon Products, chain, bar and sprocket maintenance manual (sections 1 and 2), read October 19, 2026
- HSE, AFAG308 top-handled chainsaws, rev2 April 2013, read October 19, 2026