Line-clearance pole saws and insulated poles: how OSHA 1910.269 and makers describe them
OSHA 1910.269 defines line-clearance tree trimming as work within 3.05 m (10 ft) of lines at 50 kV or less, tests live-line tool poles and sets power saw rules. Makers list pole saw heads, hot-stick adaptable heads and dielectrically tested poles.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The rule text is 29 CFR 1910.269 as published in the eCFR. The tool types come from the product category pages of two makers, one of line-clearance and utility tools and one of pole pruners.
Line-clearance tree trimming in 1910.269
The standard defines line-clearance tree trimming as the pruning, trimming, repairing, maintaining, removing or clearing of trees, or the cutting of brush, within a set distance of electric supply lines and equipment. The distance is 3.05 m (10 ft) for voltages to ground of 50 kilovolts or less. Above 50 kilovolts it is 3.05 m plus 0.10 m (4 inches) for every 10 kilovolts over 50.
The standard covers this work when it clears space around power generation, transmission or distribution lines or equipment on behalf of the organization that operates, or controls the operating procedures for, those lines. Qualified employees fall under the entire section except paragraph (r)(1). Line-clearance tree trimmers who are not qualified employees fall under paragraphs (a)(2), (a)(3), (b), (c), (g), (k), (p) and (r).
The standard defines a line-clearance tree trimmer as an employee who, through related training or on-the-job experience or both, is familiar with the special techniques and hazards involved. A trimmer is not a qualified employee unless he or she has the training required for one.
Insulating equipment for branches near conductors
Paragraph (r)(1)(iv) says branches that touch exposed energized conductors or equipment, or sit within the distances in Tables R-5 to R-8, may be removed only with insulating equipment. A note treats a tool as insulated if the employer can demonstrate insulating qualities that meet paragraph (j)(1) and the tool is clean and dry.
| Point | Wording |
|---|---|
| Design test, fiberglass-reinforced plastic | 328,100 volts per meter (100,000 volts per foot) of length for 5 minutes |
| Design test, wood | 246,100 volts per meter (75,000 volts per foot) for 3 minutes |
| Daily condition | Each tool is wiped clean and visually inspected for defects before use each day |
| Periodic test | Tools used for primary employee protection are removed from service every 2 years for examination, cleaning, repair and testing |
| In-service test voltage | 246,100 volts per meter (75,000 volts per foot) for 1 minute for fiberglass; 164,000 volts per meter (50,000 volts per foot) for 1 minute for wood |
The note to paragraph (j)(1) deems live-line tools that use rod and tube meeting ASTM F711-02 (2007) to comply with the design test. Appendix B to the standard says that between 72.6 and 800 kilovolts employees usually use live-line tools, called hot sticks there, for work on energized equipment. It adds that the tools keep the energized part at a constant distance from the employee.
Power saw paragraphs
Paragraph (r)(5) requires gasoline-engine power saw operations to meet 1910.266(e) and adds its own items.
- A power saw weighing more than 6.8 kg (15 lb, service weight) and used in trees is supported by a separate line. The exceptions are work from an aerial lift and topping or removing where no supporting limb is available.
- Each saw has a control that returns it to idling speed when released, and a clutch adjusted so it does not engage the chain drive at idle.
- A saw is started on the ground or where it is otherwise firmly supported, and may not be running while an employee carries it up a tree.
- Engines are stopped for cleaning, refuelling, adjustments and repairs, except as the manufacturer's servicing procedures require otherwise.
Tool types in makers' catalogues
One maker of utility and line-clearance tools files its tree care range under Tree Care and Line Clearance. The category tree separates the types below.
- Hand saws, loppers, and hedge and pruning shears.
- Hot-Stick Compatible Pole Attachments: adaptable pole pruners, adaptable pole saw heads, adaptable pole vine pullers and an adaptable pole wire raiser.
- Pole Attachments: pole pruners, pole saw heads, pole vine pullers, a pole wire raiser and pole adapters.
- Fiberglass poles, including a Dielectrically Tested Foam Core class with base and extension poles and a tree trimming line-clearance kit series.
- Telescoping poles in aluminum and fiberglass, and accessories such as scabbards, pruning ropes and replacement saw blades.
Its pole saw head category lists head kits with a scabbard, double-hook heads and folding heads. The same category lists a Universal Tool Adapter and a Saw Blade Universal Adapter.
A chainsaw maker's pole pruner page lists 17 models. They include battery pole pruners, models with a length-adjustable telescopic shaft, models with an anti-vibration system, and manual telescoping pole pruners.
Sources
- eCFR, 29 CFR 1910.269 (scope in (a)(1)(i)(E), paragraphs (j) and (r), and definitions), read October 21, 2026
- Jameson, Hand Saws, Loppers and Shears and the Tree Care and Line Clearance category tree, read October 21, 2026
- Jameson, Pole Saw Heads category page, read October 21, 2026
- STIHL USA, Pole Pruners product category page, read October 21, 2026