Stump grinder guards, debris curtains and exclusion distances: HSE, FACE and a maker manual
HSE calls for guarded belts and shafts and intact debris curtains but prints no clearance distance. A California FACE report cites a maker's 75 feet, and one compact-carrier grinder manual prints 9 m (30 ft) for bystanders.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. The sources are the HSE leaflet AFAG606 on mobile stump grinders, the California Department of Public Health FACE report 18CA002, and the operator's manual for one stump grinder attachment on a compact tool carrier.
Guards and curtains in HSE AFAG606
HSE leaflet AFAG606 (2013) covers mobile stump-grinding machinery and is meant for use alongside the manufacturer's handbook in a risk assessment. It lists the machine checks.
- Belts, shafts and fan blades are guarded on both the machine and the power source.
- The debris curtains around the cutting head are present, intact and adequate.
- On a machine driven by a power take-off (PTO) shaft, the shaft guard complies with BS EN ISO 5674 and encloses the shaft along its full length, from tractor to machine.
- A marked, working engine-stopping device is within the operator's reach from the normal working position.
- A fire extinguisher is readily accessible.
Before moving the machine, the leaflet has the drive to the cutting mechanism disengaged and the mechanism stopped. It also has guards and operating panels placed in the transport position before towing. Eye protection is a mesh visor to BS EN 1731 or glasses to BS EN 166. Hearing protection applies where noise exceeds 85dB(A).
Warning signs, screening and the safe working area
AFAG606 does not print an exclusion distance. It describes warning and prohibition signs, as in the Health and Safety (Safety Signs and Signals) Regulations 1996, on all reasonably foreseeable approaches to the worksite. In areas of high public access, the risk assessment may call for extra controls such as barrier tape, barriers or screens, or extra manning. Work stops if the safe working area is breached.
At the roadside, the cutting head is positioned to direct chips away from pedestrians and traffic. The leaflet adds that supplementary screening is always used to protect people and property from flying debris.
Distances in the FACE report and a maker manual
The California FACE report 18CA002 (March 25, 2019) investigated a landscaping-company fatality in 2018. A worker was pulled into the grinding wheel by a rope that was tied around his waist and fastened to an eye hook on the disc guard. The report's listed safety precautions include these.
- Check for debris and buried objects before positioning, with the machine stable.
- Use a barrier, when possible, to repel debris from the cutting action.
- Only the operator is present, and no one is within 75 feet while the grinder operates.
- Never modify or alter the grinder.
- Never attach ropes or chains to the grinder while it operates. An eye hook is for moving the machine when it is off.
The report states that the manufacturer's instruction manual for the machine involved warns against allowing additional workers within 75 feet while grinding.
The operator's manual for a stump grinder attachment on a compact tool carrier prints a different distance. Its safety section says to keep all bystanders at least 9 m (30 ft) from the work area and never to operate the grinder without the shield on the traction unit and the chip guard on the grinder. Its decals warn of a thrown-object hazard and tell users to keep all guards and shields in place. It gives a maximum stump height of 91 cm (36 inches). The chip guard has four sets of mounting holes, set higher for grinding close to the ground and lower for tall stumps.
| Source | Clearance wording |
|---|---|
| HSE AFAG606 | No distance. Signs on all foreseeable approaches, extra controls where public access is high, work stops if the safe working area is breached |
| CA/FACE 18CA002, citing a maker manual | No one within 75 feet while the grinder operates |
| Compact tool carrier attachment manual | Bystanders at least 9 m (30 ft) from the work area |
To correct or remove an entry, write to the address at the foot of this page.