ArbNation Join free

Stump height and stump cutting rules in the felling codes

None of the four codes below sets one stump height. WorkSafeBC and Alaska leave it to the faller's judgment, WorkSafeBC caps a snow depression at 45 cm, and SafeWork NSW measures the escape route from the stump.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

This page draws on what the named logging regulations and codes of practice publish. It is not training and does not teach the work.

WorkSafeBC: stump height in the faller's judgment

Part 26 of the British Columbia Occupational Health and Safety Regulation covers forestry operations. It gives no fixed stump height. On dangerous trees, section 26.26 says stump height must, in the judgment of the faller, allow maximum visibility and freedom of action.

Section 26.24 deals with the stump in two places. Where snow is packed or shovelled away to reduce stump height, the depression at the base of the tree must not be deeper than 45 cm (18 in). The same section lists the procedures for falling a tree. The backcut must be higher than the undercut, to leave a step on the stump. The undercut must be sufficient, complete and cleaned out, and enough holding wood must remain. Wedging tools must be immediately available, and wedges must be set unless the tree has a pronounced favourable lean.

Before a tree is felled, section 26.24 clears all workers from a radius of two tree lengths. All obstructions to the work must be cleared, and a safe escape route to a predetermined safe position must be prepared.

Alaska: additional logging standards

The Alaska Department of Labor publishes Additional Logging Standards, adopted by reference under 8 AAC 61.1060. The danger tree rule is close to the British Columbia one. Stump heights must be the height that, in the cutter's judgment, allows maximum safety during the falling operation. Danger trees are felled in the direction of lean wherever possible, with as deep an undercut as possible to avoid vibration from using wedges.

SafeWork NSW: the stump as the start of the escape route

The SafeWork NSW Tree works code of practice, approved under section 274 of the Work Health and Safety Act 2011 and in force from March 27, 2026, replaces the 1998 Amenity Tree Industry code. Its felling controls include a minimum 45-degree escape route extending at least 6 metres from the stump. Figure 8 in the code shows the 45-degree escape route running to an area at least 6 metres away from the stump. Where that route cannot be made, the code points to alternative escape routes or other suitable control measures.

WorkSafe New Zealand: cut height and the stump as an anchor

The Approved Code of Practice for Safety and Health in Arboriculture, November 2012, sets no stump height in numbers either. It ties the height of the cuts to the ground. Scarf and back cuts are made at a height above the highest ground level that lets chainsaw operators safely begin the cut, control the tree and have freedom of movement for escape. Scarf cuts are required on all trees and trunks over 125 mm at breast height. The back cut must not penetrate into the predetermined hinge area.

The same code deals with a stump used as a ground anchor. When a stump anchors winching or secures pulling blocks, it must be of sufficient size and stability for the winching operation. Strops used to anchor winches or pulling blocks must be at least 1.5 times the safe working load of the pulling rope.

Stumps as anchors and as hazards

Section 26.40 of the British Columbia regulation lets a standing tree anchor lines or blocks only if no suitable stump is available and the tree is tied back to another anchor. A stump or tree cannot serve as an anchor until it has been found suitable, and it must be inspected daily afterward. An anchor for a haulback block needs a notch deep enough to retain the strap.

The Alaska standards also cover guylines. Stumps used to fasten guylines and skylines must be carefully chosen for position, height and strength, and tied back if necessary. They are notched and barked where the wraps go. Workers stand behind the stump in the clear while the wraps are tightened. The standards set no fewer than two and one-half wraps, with at least six staples or eight railroad spikes driven into sound wood on the first and last wraps.

The British Columbia regulation also covers stumps left near roads. Section 26.82 says dangerous trees, loose rocks, stumps and other unstable materials that are hazardous to road users must be removed or cleared for a safe distance back from roadsides or roadside banks.

Where the figures differ

BodyStump heightRelated figure
WorkSafeBC, Part 26Faller's judgment on dangerous treesSnow depression no deeper than 45 cm (18 in)
Alaska Additional Logging StandardsCutter's judgment on danger treesTwo and one-half wraps on guyline stumps
SafeWork NSW Tree works codeNo height givenEscape route at least 6 m from the stump
WorkSafe NZ arboriculture codeCuts above the highest ground levelScarf cuts on trunks over 125 mm

Sources