Using a chainsaw from an aerial platform: what OSHA, HSE and WorkSafeBC publish
HSE says chainsaws are not used off the ground without training and that two people are present. OSHA 1910.67 and WorkSafeBC 13.33 require a fall arrest or restraint system on the basket.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. None of the four texts has a clause headed "chainsaw from a platform". Each one covers a piece of it: the platform, the saw, or the person on both.
HSE on aerial tree work
HSE's page on aerial work says work off the ground that involves lifting and lowering people or loads will be subject to the Work at Height Regulations 2005 and the Lifting Operations and Lifting Equipment Regulations 1998. That includes work-positioning techniques. It then sets out three points.
- Chainsaws should never be used off the ground unless the operator has been adequately trained in safe working techniques.
- A minimum of 2 people must be present during all aerial work.
- One of the ground team must be available, competent and equipped to do an aerial rescue without delay.
HSE adds that professional chainsaw operators in forestry and arboriculture must be trained and competent for the work. It names Lantra Awards and City and Guilds NPTC as the awarding bodies. Another guide covers the City and Guilds MEWP chainsaw award handbook. HSE content is published under the Open Government Licence v3.0.
OSHA on the aerial lift
29 CFR 1910.67 covers work platforms mounted on vehicles. Its definition of an aerial device is any vehicle-mounted device, telescoping or articulating, used to position personnel. Paragraph (c)(2) lists the rules for extensible and articulating boom platforms.
- Only trained persons operate an aerial lift.
- A personal fall arrest or travel restraint system meeting subpart I is worn and attached to the boom or basket.
- Belting off to an adjacent pole, structure or equipment is not permitted.
- Employees stand firmly on the basket floor and do not sit or climb on its edge.
- Climbers are not worn while working from an aerial lift.
- Boom and basket load limits set by the maker are not exceeded.
- Brakes are set, and outriggers sit on pads or a solid surface.
An aerial lift truck may not be moved with the boom raised and people in the basket, except equipment built for that operation. Lift controls are tested each day before use.
OSHA on the saw and the cut protection
29 CFR 1910.266 is the logging operations standard, and its scope is logging of every end use. Paragraph (d)(1)(iv) requires leg protection of cut-resistant material, such as ballistic nylon, for each employee who operates a chain saw. It covers the thigh to the top of the boot. The paragraph carves out two cases:
- a climber, where the employer shows a greater hazard from wearing it;
- an employee working from a vehicle-mounted work platform that meets 1910.67.
Paragraph (e)(2) holds the saw rules. A chain saw put into service after the effective date has a chain brake and meets ANSI B175.1-1991. No kickback device is removed or disabled. A gasoline saw has a continuous pressure throttle control that stops the chain on release. The saw is started on the ground or where otherwise firmly supported, and drop starting is prohibited. The operator is certain of footing before cutting. The saw is not used in a position or at a distance that could leave the operator off-balance, with insecure footing, or without a firm grip. The saw is not used to cut directly overhead.
WorkSafeBC on elevating work platforms
Part 13 of the Occupational Health and Safety Regulation defines an elevating work platform as a movable work platform that raises itself to overhead work locations. Section 13.33(1) requires a person on one to wear a personal fall arrest system secured to a suitable and substantial anchorage point. Section 13.33(1.1) exempts a person on a scissor lift, or a platform with similar characteristics, on a firm level surface with no irregularities, if all guardrails and chains are in place.
Three more sections shape the platform itself.
- Section 13.21: the maker's operation manual is available at the workplace for each platform in use.
- Section 13.23: a vehicle-mounted platform is inspected at least every 12 months and certified in writing by the maker or a professional engineer.
- Section 13.26: controls are hold-to-run, each set has a red emergency stop, and a marked overriding lowering control lets a worker at the lower controls lower the platform in an emergency.
Where the four texts line up
| Topic | What the texts publish |
|---|---|
| Training | HSE: chainsaw operators trained for work off the ground. OSHA 1910.67(c)(2)(ii): only trained persons operate an aerial lift. |
| Fall protection on the basket | OSHA 1910.67(c)(2)(v): fall arrest or travel restraint system. WorkSafeBC 13.33(1): personal fall arrest system. HSE: Work at Height Regulations 2005 apply. |
| Second person | HSE: at least 2 people present, one able to rescue without delay. |
| Saw leg protection | OSHA 1910.266(d)(1)(iv): exception for a vehicle-mounted platform. HSE: appropriate personal protective equipment. |
The OSHA leg protection exception and the HSE personal protective equipment line do not match. The OSHA text exempts a platform worker from chain saw leg protection when the platform meets 1910.67. HSE sets no such exception on its aerial work page.
Sources
- Health and Safety Executive, Tree work: aerial work, page dated September 22, 2026, read October 19, 2026
- eCFR, 29 CFR 1910.67 vehicle-mounted work platforms, read October 19, 2026
- eCFR, 29 CFR 1910.266 Logging operations, read October 19, 2026
- WorkSafeBC, Occupational Health and Safety Regulation Part 13, Ladders, scaffolds and temporary work platforms, read October 19, 2026