ArbNation Join free

What the plate says: certification label, vehicle plate and compliance plate in the US, UK and Australia

US federal rules list GVWR and GAWR on a certification label. The UK shows maximum authorised mass on a plate or sticker. Australian Design Rule 61/02 requires a compliance plate and, on heavy vehicles, a vehicle plate.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The guide to GVWR and GCWR in the United States explains the weight terms.

United States: the certification label

The rule is 49 CFR 567.4, requirements for manufacturers of motor vehicles. It makes the manufacturer affix a label to each vehicle. The label is riveted or permanently affixed so that it cannot be removed without destroying or defacing it. Replica vehicles and vehicles built in two or more stages are outside this paragraph.

Where the label sits depends on the vehicle.

  • Most vehicles: the hinge pillar, door-latch post or door edge next to the driver's seating position, easily readable without moving anything except an outer door.
  • Trailers: the forward half of the left side, easily readable from outside without moving any part of the vehicle.
  • Motorcycles: a permanent member close to the steering post and handlebars.

Paragraph (g) lists the statements, in English block capitals at least three thirty-seconds of an inch high:

  1. The manufacturer's name, after the words "Manufactured By" or "Mfd By".
  2. The month and year of manufacture.
  3. The Gross Vehicle Weight Rating (GVWR) in pounds.
  4. The Gross Axle Weight Rating (GAWR) in pounds for each axle, front to rear.
  5. A statement that the vehicle meets the federal motor vehicle safety standards in effect on the date of manufacture.
  6. The vehicle identification number.
  7. The type classification, such as truck, MPV, bus or trailer.

The rule sets a floor for the GVWR figure. It may not be less than the unloaded vehicle weight plus rated cargo load plus 150 pounds for each designated seating position. A manufacturer may list more than one GVWR and GAWR set, each tied to a tire size. A combined weight rating is not among the listed statements.

United Kingdom: the plate or sticker

GOV.UK defines maximum authorised mass (MAM) as the weight of a vehicle or trailer with the maximum load carried safely on the road. It gives two other names for it: gross vehicle weight (GVW) and permissible maximum weight. The figure is listed in the owner's manual and is normally shown on a plate or sticker fitted to the vehicle.

The plate or sticker may also show a gross train weight (GTW), also called gross combination weight (GCW). GOV.UK defines it as the total weight of the tractor unit plus trailer plus load. A vehicle unlikely to reach its maximum may be "down-plated", which means a lower weight is shown on the plate or sticker. The GOV.UK towing page also places the MAM on a plate or sticker on the vehicle or trailer. It uses the figure for licence limits. A licence held before 1 January 1997 usually covers a combination up to 8,250 kg MAM. A licence from that date covers a trailer up to 3,500 kg MAM. GOV.UK content is published under the Open Government Licence v3.0.

Australia: ADR 61/02 vehicle marking

Australian Design Rule 61/02 is the vehicle standard for vehicle marking, made by the Minister under the Motor Vehicle Standards Act 1989 and dated 29 November 2005. The text described here is that 2005 version as registered. It applies to categories from mopeds to heavy trailers made on or after 1 July 1995, with ADR 61/01 as an acceptable prior rule.

Clause 5 requires a unique vehicle identification number that meets ISO 3779, ISO 3780 and ISO 4030, with FMVSS 115 and Australian Standard MP 55-1988 deemed equivalent. Clause 6.1 says every motor vehicle and every applicable trailer must bear an approved compliance plate in a conspicuous position.

Clause 8 adds a separate vehicle plate on every ME, NC and T-group vehicle. Those categories are heavy omnibuses, heavy goods vehicles and trailers. The plate is embossed, indented, etched or engraved on a durable label, welded, riveted or otherwise permanently attached in a readily visible position. Its characters are at least 2.5 mm high. Clause 8.3 says a separate vehicle plate need not be fitted where the compliance plate holds all the required information.

ADR 61/02 clause 8.1.2: what the vehicle plate carries
ItemWhich vehicles
Manufacturer's name, model, identification numberAll plated vehicles
Date of manufactureUnless a compliance plate is fitted
Gross combination mass, kgNC heavy goods vehicles
Maximum towing capacity, the aggregate trailer mass the towing vehicle is built for, kgME heavy omnibuses
Aggregate trailer mass, kgTrailers

Further words are required on particular vehicles. A heavy goods vehicle built for road trains or B-doubles carries ROAD TRAIN or B-DOUBLE. A trailer built for road trains up to 125 t gross combination mass carries ROAD TRAIN TRAILER. B-double trailers with ADR 38/01 antilock systems carry a statement saying so.

Sources