ArbNation Join free

Aerial device inspection intervals: Great Britain, British Columbia, Victoria and the United States

Great Britain sets a 6-month thorough examination for lifting equipment that carries people. British Columbia sets a 12-month inspection and written certification for vehicle-mounted platforms. OSHA names a daily control test.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The facts on this page come from the named regulators and standards bodies. It is not training and does not teach the work.

Intervals by jurisdiction

Inspection and examination intervals for lifting equipment that carries people
JurisdictionInstrumentInterval as printed
Great BritainLifting Operations and Lifting Equipment Regulations 1998, regulation 9Thorough examination at least every 6 months for lifting equipment for lifting persons, and for accessories for lifting. At least every 12 months for other lifting equipment. Or under an examination scheme.
British ColumbiaOHS Regulation, section 13.3Inspection of a work platform and its components before use on each shift, and after any modification
British ColumbiaOHS Regulation, section 13.23Inspection at least every 12 months, in line with good engineering practice, plus written certification
United States29 CFR 1926.453(b)(2)(i)Lift controls tested each day prior to use
VictoriaWorkSafe Victoria, EWP industry standard, Edition 4Inspection and maintenance requirements and a pre-operational checklist. No interval is printed on the WorkSafe page.

Great Britain: regulation 9

The Lifting Operations and Lifting Equipment Regulations 1998 put the duty on the employer. Regulation 9(1) calls for a thorough examination for any defect before lifting equipment is first put into service. The exception is equipment that has not been used before and comes with a declaration of conformity made not more than 12 months earlier.

Regulation 9(2) adds an examination after installation, and after assembly at a new site or location, where safety depends on installation conditions. Regulation 9(3) applies to equipment exposed to conditions that cause deterioration liable to result in dangerous situations. It sets thorough examination at least every 6 months for equipment for lifting persons or an accessory for lifting, and at least every 12 months for other lifting equipment. A third route is an examination scheme. A further examination follows each time exceptional circumstances liable to jeopardise safety have occurred.

Between thorough examinations, regulation 9(3)(b) calls for inspection by a competent person at suitable intervals, if appropriate for the purpose. Regulation 9(4) bars lifting equipment from leaving an undertaking, or being used by a second employer, unless it travels with physical evidence of the last required thorough examination. The regulation has been in force since December 5, 1998.

British Columbia: sections 13.3, 13.22 and 13.23

Part 13 of the Occupational Health and Safety Regulation covers ladders, scaffolds and temporary work platforms. Section 13.3 calls for inspection of a work platform and its associated components before use on each shift and after any modification. Any condition that might endanger workers must be remedied before use.

Section 13.23(1) covers a vehicle-mounted work platform and a self-propelled boom-supported work platform. Each must be inspected in accordance with good engineering practice at least every 12 months. Each must also be certified in writing by the equipment manufacturer or a professional engineer as complying with Part 13 and safe for use. The regulation defines boom-supported as supported by a device that telescopes, articulates, rotates or extends relative to the machine base or vehicle.

Section 13.22 puts record keeping on the employer. If inspection and maintenance records, other than pre-shift inspections, are not available, the equipment must not be used until the manufacturer or a professional engineer has inspected and certified it safe.

United States: OSHA and ANSI A92.2

Under 29 CFR 1926.453(b)(2)(i), lift controls are tested each day prior to use to determine that they are in safe working condition. Paragraph (b)(2)(xii) adds that before moving an aerial lift for travel, the boom is inspected to see that it is properly cradled and the outriggers are stowed.

Section 1926.453(a)(1) ties design and construction to ANSI A92.2-1969. A letter of November 8, 2005 from OSHA's Directorate of Construction explains that employers using the later A92.2-1979 or A92.2-1990 editions meet that paragraph, and that A92.2-2001 section 4.1 is identical to the 1990 text. The letter adds that the OSHA aerial lift standard continues to require only compliance with the 1969 edition.

Victoria: the industry standard

WorkSafe Victoria published Edition 4 of the Elevating Work Platforms industry standard on June 23, 2023, as an 80-page PDF. It covers inspection and maintenance requirements, a pre-operational checklist, harness inspection, and the training and competency of people who use, observe or spot an EWP. Among the Australian Standards behind it is AS 2550.10:2006, Cranes, hoists and winches, Safe use, Mobile elevating work platforms (MEWPs).

Sources