CSA B354 series and Canadian MEWP operator training rules by province
Ontario's construction regulation names the CSA B354 standards and sets out operator instruction in section 147. British Columbia points to CSA or ANSI standards, and Alberta's boom platform rule covers fall protection.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. Provincial rules cover elevating work platforms (EWPs). Of Ontario, British Columbia and Alberta, only Ontario names CSA B354. For the US standard, see the guide to ANSI A92.24 operator training.
Ontario: the B354 standards and operator instruction
The Infrastructure Health and Safety Association (IHSA) summarizes Ontario's Regulation for Construction Projects, O. Reg. 213/91. Section 144 requires an EWP to be designed by an engineer to the applicable National Standard of Canada. The regulation's table pairs each type of platform with a standard.
| Type of platform | Standard in the table |
|---|---|
| Rolling EWP | CAN3-B354.1-M82 |
| Self-propelled EWP | CAN3-B354.2-M82 and CAN3-B354.3-M82 |
| Boom-type EWP | CAN3-B354.4-M82 |
| Vehicle-mounted aerial device | CAN/CSA-C225-10 |
The platform must support a rated working load of at least 1.3 kilonewtons and be tested to the standard in the table. It may be used only if an engineer has certified in writing that it complies, and the certification includes the details of testing. It carries guardrails and signs. The signs show the rated working load, the limits on outriggers and surface conditions, the manufacturer's warnings, the name and number of the standard, and the owner's name and address.
Section 147 covers the operator. Before first use on a platform, a worker is given oral and written instruction and is trained to operate that class of EWP. The instruction includes these four items.
- The manufacturer's instruction.
- The load limitations.
- A hands-on demonstration of the proper use of all controls.
- The limits on the kinds of surfaces the platform is designed for.
Section 96 adds that a worker operates powered equipment on a project only when competent to do so, with an exception for a worker being instructed and supervised by a competent person. A trained worker inspects the platform each day before use, following the manufacturer's instructions.
Ontario also keeps the owner's paper trail. Under section 145, the owner keeps a permanent record of inspections, tests, repairs, modifications and maintenance. It runs from the date of purchase or May 10, 1991, whichever is later, with the name and signature of each person who did the work. Section 146 puts a maintenance and inspection record tag near the operator's station. Section 149 keeps the operator's manual with the platform on a project.
British Columbia: Part 13 of the OHS Regulation
WorkSafeBC's Occupational Health and Safety Regulation does not name B354 in the Part 13 text. Section 13.2 says a work platform must meet and be used in accordance with the applicable CSA or ANSI standard in effect when it was made, unless the Board decides otherwise. Another standard acceptable to the Board, or the requirements of a professional engineer, can stand in where no standard applies.
For each EWP in use, section 13.21 requires the manufacturer's operation manual at the workplace and the maintenance manual reasonably available to workers. Under section 13.22, the employer keeps records of inspection, maintenance, repair or modification, and the platform is not used without them until the manufacturer or a professional engineer has inspected and certified it safe. Section 13.23 sets a 12-month inspection for a vehicle-mounted platform and for a self-propelled boom-supported platform. The manufacturer or a professional engineer certifies it in writing. Section 13.33 requires a person on an EWP to wear a personal fall arrest system, with an exemption for scissor lifts on a firm level surface with all guardrails and chains in place.
Part 13 has no operator-training section for these platforms.
Alberta: section 156 of the OHS Code
Part 9 of Alberta's Occupational Health and Safety Code deals with fall protection. Section 156 says an employer must see that a worker on a boom-supported EWP, aerial device or forklift work platform uses a personal fall arrest system. It connects to the manufacturer's anchor or, where none is specified, to an engineer-certified anchor meeting CSA Z259.16-04. The lanyard is short enough, where reasonably practicable, to stop a worker being ejected. Scissor lifts get a travel restraint system, and the section sets exceptions for guardrail-only work on a firm, substantially level surface. The section names CSA Z259.16-04, not B354.
Sources
- Infrastructure Health and Safety Association (Ontario), Elevating Work Platforms, quoting O. Reg. 213/91 sections 96 and 144 to 149, read October 15, 2026
- WorkSafeBC, Occupational Health and Safety Regulation, Part 13 Ladders, Scaffolds and Temporary Work Platforms, read October 15, 2026
- Government of Alberta, Occupational Health and Safety Code, Part 9 Fall Protection, section 156, read October 15, 2026