ArbNation Join free

Anchor sling and strap ratings: MBS marking, EN 566 and EN 795 anchor device coverage

EN 566 covers mountaineering slings and EN 795 covers removable single-user anchor devices. The ICoP sets a minimum breaking strength of 18 kN for temporary anchor devices and 22 kN for connectors.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The Industry Code of Practice for Arboriculture: Tree Work at Height (ICoP, Edition 2, May 2020) uses minimum breaking strength, or MBS, as its rating for tree climbing equipment.

Two standards, two kinds of product

StandardWhat the BSI entry covers
EN 566, Mountaineering equipment. SlingsSafety requirements and test methods for slings used for mountaineering, including climbing. BS EN 566:2017 was published March 31, 2017, and is listed as current and under review. It replaces EN 566:2006, which is withdrawn. The technical changes were to the stability test requirement and method and to the test conditions. The BSI record lists stitching, tensile strength, marking and instructions for use among its subjects.
EN 795, Personal fall protection equipment. Anchor devicesPerformance requirements and test methods for single-user anchor devices that are intended to be removable from the structure. They incorporate stationary or travelling anchor points for attaching parts of a personal fall protection system. The standard also gives marking, instructions for use and installation guidance. BS EN 795:2012 replaces EN 795:1996, which is withdrawn.

EN 795 does not apply to anchor devices for more than one user at a time or to anchor devices used in sports or recreation. BSI also lists equipment made to EN 516 or EN 517, structural anchors, and parts of structures installed for other purposes, such as beams and girders.

The 2012 edition replaced the old classes of anchor device, A, B, C and so on, with types. BSI puts the reason as a plainer picture of how the anchor devices differ.

The ICoP figures

The ICoP separates temporary anchor devices from artificial anchors. It names tape slings and cambium or pulley savers as typical temporary anchor devices. Under clause 3.10.6.2, a temporary anchor device must be made to the standard for temporary anchors and must have an MBS of at least 18 kN. It must be configured so that it cannot slip up or down the stem. Any connector used with it must be configured to prevent minor axis or cross-loading and inadvertent opening.

ICoP clauseItem and requirement
3.10.6.2Temporary anchor devices: MBS of at least 18 kN.
3.10.6.5Connectors: MBS of at least 22 kN, with the major axis loaded where applicable.
3.10.6.8Rope: 15 kN new with a termination, 22 kN new without one.
3.10.6.10Lanyards: MBS of at least 15 kN.
3.10.6.13Slings and strops: the safe working load is known. High modulus fibres may give greater strength for their weight but may be less abrasion-resistant.

Marking

ICoP clause 3.11.6 asks that all equipment be marked so it can be identified and traced. The marking varies between items, but information on safe use and operating parameters should be displayed. Clause 3.10.6.1 adds that each item should carry enough information to trace it to the manufacturer, product name, construction properties and examination records.

The ICoP standards list in Part 6 includes BS EN 566 for slings, BS EN 795 for anchor devices, BS EN 362 for connectors and BS EN 354 for lanyards. The UIAA list has its own number for slings, UIAA 104, and separate numbers for tape and accessory cord.

Gaps in the sources

The BSI pages give titles, scopes and edition dates for the two standards. They do not print the marking layout or a kN figure. The 18 kN and 22 kN figures above come from the ICoP alone.

Sources