Anchor checks in the codes: OSHA, WorkSafeBC, HSE, the UK industry code and NSW
The codes ask for anchors that are assessed before use, and one New South Wales code adds proof loading. ISA's Z133-2026 notice prints no anchor clause. OSHA, WorkSafeBC, HSE and the UK industry code set the other wording.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
Anchor checks in tree climbing are described below as OSHA, WorkSafeBC, HSE, the UK industry code, SafeWork NSW and an Australian training unit publish them. It is not training and does not teach the work.
Anchor wording by country
| Country and body | Anchor wording |
|---|---|
| United States, ANSI Z133 (ISA) | ISA announced the Z133-2026 Safety and Health Requirements standard as available on 27 May 2026. The announcement gives the release and scope. It prints no anchor test clause. |
| United States, OSHA 1910.140 | Anchorages for personal fall protection must be independent of any anchorage that suspends workers or platforms. They must support at least 5,000 pounds (22.2 kN) for each worker attached. The other route is design, installation and use under the supervision of a qualified person, as part of a complete system with a safety factor of at least two. |
| Canada, WorkSafeBC OHS Regulation 26.12.0.4 | A qualified arborist or trainee arborist must assess and determine that each anchor point is suitable for the loads to be imposed on it before using it. Climbing lines use independent anchor points if practicable. |
| United Kingdom, HSE | In the tree, the system should where possible be attached to two anchor points that carry load. Each should be strong enough to support the climber, the equipment and any foreseeable loading. |
| United Kingdom, ICoP Tree Work at Height, Edition 2 | The anchor point of a personal fall protection system must be unquestionably reliable and able to withstand any foreseeable loading throughout the task. A backup uses an independent anchor where possible. |
| Australia, SafeWork NSW Tree works code | Section 4.3 asks for proof loading and testing before climbing, where practicable. It also asks whether a weight test has been completed on natural anchor points. |
| Australia, AHCARB319 | Performance criterion 3.3 is to inspect and test remotely installed anchor points to confirm they are secure before use. |
United States
The Z133-2026 release notice is the only Z133 text opened. It calls the standard the US safety standard for arboricultural operations and says the digital version is a free PDF for individual use. OSHA 1910.140 is the general industry rule on personal fall protection systems.
OSHA 1910.140 also says systems must be inspected before initial use during each workshift for mildew, wear, damage and other deterioration. A system or component that has taken impact loading is removed from service until a competent person inspects it and finds it undamaged. The rule defines an anchorage as a secure point of attachment for lifelines, lanyards or deceleration devices.
Canada
WorkSafeBC's forestry operations part sets a tree-climbing plan. For each tree to be climbed, the plan identifies the climbing system and the type and location of the initial anchor point. Regulation 26.12.0.4 then sets the assessment duty, in force since December 1, 2021. The same part has a separate rule for anchors that hold lines and blocks. A stump or tree must not anchor a line or block until it has been determined suitable, and it is inspected daily. Regulation 26.12.0.6 adds that a qualified arborist inspects the whole tree-climbing system before it is first used on each work shift.
United Kingdom
HSE's climbing page applies the Work at Height Regulations 2005. It describes work positioning and rope access techniques. Where a backup system is not reasonably practicable, it lists choosing reliable anchor points among the ways to keep a work positioning system from failing. The industry code adds figures for temporary anchor devices such as tape slings. They must be made to the standard for temporary anchors, set so they cannot slip up or down the stem, and carry a minimum breaking strength of at least 18 kN. Artificial anchors such as machinery need enough mass and ground friction that they cannot move.
Australia
SafeWork NSW calls for every anchor point to be carefully assessed as safe and suitable for the work. Its checklist asks about defects in the tree, whether the anchor can support the force of a fall, two people and rescue loads, and whether it keeps the worker from swinging toward electrical conductors. The proof loading line sits in that checklist. AHCARB319 is a training unit, not a regulator's text. Its criterion 3.2 covers installing low-risk anchor points with throw lines.
Sources
- International Society of Arboriculture, Z133-2026 Safety and Health Requirements standard is now available (newsroom), read October 16, 2026
- US Occupational Safety and Health Administration, 29 CFR 1910.140 Personal fall protection systems, read October 16, 2026
- WorkSafeBC, Occupational Health and Safety Regulation Part 26 Forestry operations, sections 26.12.0.3, 26.12.0.4 and 26.40, read October 16, 2026
- Health and Safety Executive, Tree climbing: climbing operations, read October 16, 2026
- Arboricultural Association and partners, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, sections 3.8 and 3.10.6.2, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, section 4.3, read October 16, 2026
- Australian Government, Skills Insight, AHCARB319 Use arborist climbing techniques, Release 1, read October 16, 2026