ArbNation Join free

Caught in or between: chippers, stump grinders and winch lines in tree work, what OSHA, NIOSH and HSE list

OSHA counted 39 chipper deaths from 1996 to 2005 and found 78 percent were caught-in events. Its bulletin, NIOSH Hazard ID 8 and two HSE leaflets list the machine guards, stop devices and work practices they link to those hazards.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work.

The hazard group

The OSHA tree care page sorts fatal tree work events into six groups: asphyxia, caught-in, electrocution, falling, struck-by and other. Under caught-in it lists two reports from the NIOSH Fatality Assessment and Control Evaluation (FACE) program. One is the New York wood chipper report 16NY024, covered in the guide to that FACE case. The other is the California stump grinder report 18CA002.

The OSHA page also points to two longer documents on chippers: OSHA Safety and Health Information Bulletin SHIB 04-16-2008, Hazards of Wood Chippers, and NIOSH Hazard ID 8, publication 99-145.

Counts

Chipper death counts as printed in two federal documents
DocumentPeriodDeaths
NIOSH 99-1451992 to 199711 workers near mobile wood chippers
OSHA SHIB 04-16-20081996 to 200539 employees in chipper accidents

NIOSH takes its 11 from the Bureau of Labor Statistics Census of Fatal Occupational Injuries. In seven, the victim was caught by the feed mechanism and pulled through the knives. In four, the victim was struck by a hood that separated after being opened or closed while knives were still rotating. OSHA takes its 39 from its Integrated Management Information System. Of those, 78 percent were caught in the chipper and most of the rest were struck-by.

NIOSH received two more reports of chipper deaths in 1998. It says they illustrate the two most common causes of fatal injury: being fed through the chipper knives and being struck by the chipper disc hood.

The chipper in the bulletins

Both bulletins describe a self-feeding chipper as a powered feed mechanism, knives on a rotating disc or drum, and an engine. Feed rollers grab branches from the infeed chute and force them into knives that rotate between 1,000 and 2,000 revolutions per minute. A removable hood covers the disc or drum for maintenance.

NIOSH names the caught-by hazard: workers feeding material are at risk of being fed through the knives if they reach or fall into the infeed hopper or become entangled in branches. The struck-by hazard comes from hoods that are unlatched, improperly secured, damaged or poorly maintained.

Listed controls

OSHA states that employees must be protected from contact with knives, feed rollers and discharge spouts. It cites the general industry machine guarding standard, 29 CFR 1910.212(a)(1) and (a)(3), and the logging standard, 29 CFR 1910.266(h)(4), which requires infeed and outfeed chutes to be guarded where the logging standard applies.

The SHIB describes these chipper safety devices as available on some machines:

  • A feed control bar that stops the rollers in the centre position and reverses them toward the spout. ANSI Z133.1-2006 requires quick-stop and reverse devices on chippers with a mechanical feed control bar.
  • A bottom feed stop bar that cuts all power when 34 pounds of force are applied to the lower edge of the feed table, and a separate panic bar that stops the hydraulic feed system.
  • Emergency pull ropes along both sides of the infeed throat, which OSHA notes can be hard to find if tangled in branches.
  • Feed tray extensions that can add as much as four feet to the infeed area.
  • Rubber curtain flaps, a discharge spout deflector and a hood safety latch that blocks starting before the hood is locked and opening before the disc has stopped.

NIOSH lists work practices for employers to cover: at least two workers in close contact, close-fitting clothing, gloves without cuffs, hands and feet outside the hopper, and feeding butt end first. OSHA lists a safety watch stationed near the shut-off devices and standing to the side of the infeed chute. Both list a daily inspection of hood latches, pins and hinges, and both state that the hood stays shut until internal parts have fully stopped. OSHA adds lockout and tagout under 29 CFR 1910.147 before servicing.

Winch lines on chippers

The SHIB describes a fatality in Idaho involving a chipper with a winch line, a hazard it calls unique. The winch sits above and in front of the infeed chute. A slack section of line tangled in a limb being fed was pulled into the cutter drum, and the line and choker snapped back with fatal force despite approved head protection.

In the SHIB's account, the chipper maker responded with a detachable choker, a larger loop on the winch line, a lighter line, a storage hook and warning signs. New models get an interlock that requires the line to be stored before the rollers run. OSHA says employers with winch-equipped chippers should contact their supplier and train employees on pinch points.

Stump grinders and other machinery in Britain

HSE's page on machinery and hand tools in forestry or arboriculture covers woodchippers, brushcutters, stump grinders, flails and mulchers. It says this equipment does not cause as many serious accidents as chainsaws, but accidents and risks remain to assess and control. Operators are to be trained and competent.

HSE leaflet AFAG606, Mobile stump grinders, lists guarding of belts, shafts and fan blades, debris curtains around the cutting head, and a PTO shaft guard to BS EN ISO 5674 on tractor-driven machines. It lists a marked engine-stopping device within reach of the operator and states that the cutting mechanism is not approached until it has come to a complete stop. Before work on the cutter, it lists the stopping device applied, the key removed and the mechanism secured.

Where the rules apply

OSHA says the SHIB is not a standard, creates no new legal obligations and is advisory. Citations rest on standards, regulations and the General Duty Clause. For related reading see the guide to lockout before clearing a chipper jam and the guide to stump grinder injuries.

Sources