ArbNation Join free

Felling rules in Great Britain: what HSE and the FISA guides publish

In England, Scotland and Wales the Health and Safety Executive sets out felling guidance and links to the Forest Industry Safety Accord. FISA publishes the guides FISA 302 on basic felling, FISA 307 on large trees and FISA 310 on winches.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The named codes and training bodies are described here as published. It is not training and does not teach the work. Some wording is adapted from Health and Safety Executive (HSE) pages published under the Open Government Licence v3.0.

Training and risk assessment

The HSE page on working with chainsaws states that, by law, chainsaw operators must have received adequate training relevant to the type of work they do, and must wear appropriate chainsaw protective clothing. HSE says its investigations show most fatal and major injuries involve operators taking shortcuts and not following good practice guidance, usually to save time.

HSE sets out key lessons for tree felling in the order of a job. Where possible a site survey comes first, so equipment, staff and hazards are known in advance. The risk assessment covers the hazards of the given site, task and tree, and HSE says it is not just a paper exercise: if risks cannot be controlled to acceptable levels, work on that task must not proceed. Emergency plans are made in advance, with first aid, emergency contact numbers, an Accident and Emergency number and the site location. The whole team plans, agrees and understands the job.

On competence, HSE warns that people holding only CS 30 and 31 with little additional experience can quickly meet situations beyond their skills. It names larger, awkward fells and the particular hazards of arboricultural work in gardens.

Cuts, aids and escape routes

HSE says control of the fell comes from a combination of the directional or sink cut, the hinge and the main felling or back cut. The cuts are right for the size and form of the tree and consistently accurate. Felling aids such as breaker bars and wedges are matched to the tree, identified in advance and ready to hand. Escape routes are planned in advance and clear of obstructions. HSE raises the possibility that the tree falls towards the escape route, and asks whether enough back-up is in place for the tree to fall as intended.

Machines, winches and pulling lines

HSE flags three areas needing particular care: machine-assisted takedown, winches in directional felling, and steep ground. Its machine-assisted takedown page notes many incidents with machines used on large edge trees and on hung-up or leaning trees. The winch page covers a tractor winch or hand winch in directional felling and assisted takedown. It does not cover timber extraction or towing. It has the chainsaw operator in control, an emergency stop obeyed at once, and any unclear signal taken as a stop. The FISA 310 page gives the detail.

The FISA felling guides

The Forest Industry Safety Accord (FISA) numbers its chainsaw guides in the 300s.

  • FISA 302, basic chainsaw felling and manual takedown. It holds industry-agreed working practices for felling and takedown with a chainsaw, last updated June 2018. It leaves out trees too small for a sink cut, and felling where wire cable, rope or machinery directs the fall. HSE cites AFAG 302, under the same title, for its danger zone figure.
  • FISA 307, chainsaw felling of large trees. It covers felling and crown breakdown of large trees in plantations, and of single large trees. It leaves out exceptional cases where the risk assessment shows advanced or alternative techniques are needed. For those, the guide calls for specialist advice and agreed safe methods.

The HSE chainsaw page also links to the FISA website, to the INDG 317 leaflet Chainsaws at work and to the top-handled chainsaws guide, AFAG 308.

Terms

HSE defines the sink cut as a triangular cut near the base on the side the tree is to fall, at an angle of approximately 45 degrees. The felling cut is the horizontal cut at the rear, just above and towards the sink cut. It should stop before it meets the sink cut to create a hinge. HSE adds that the hinge lets the felling direction and rate of fall be controlled. Further names for these cuts, by country, are in the names of notches and back cuts.

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0.

Sources