Home-made and modified gear: what the ICoP, codes and a maker notice print
The UK industry code limits alterations to the manufacturer or a competent person with its consent. New South Wales and New Zealand codes also speak to modifications, and one maker notice bars repairs outside its own facilities.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and a maker notice are described here as published. It is not training and does not teach the work.
The UK industry code
The Industry Code of Practice for Arboriculture: Tree Work at Height (Arboricultural Association, Edition 2, May 2020) deals with alterations in clause 3.11.9. It says alterations and modifications should only be carried out by the manufacturer, or by a competent person with the consent of the manufacturer or its chosen representative.
A footnote on maintenance adds that any action outside the manufacturer's authorisation could count as alteration or modification. The code says such an item could be unsafe or non-compliant.
Other clauses touch the same ground.
- Clause 3.10.4 lists the warnings a maker supplies. One is against aftermarket alterations, additions, modifications or repairs.
- The same clause says equipment used or loaded in a way the maker did not prescribe must be approved in writing by the maker or its appointed representative.
- Clause 3.10.6.8 says splices in rope are only formed by the manufacturer or with its consent, against validated performance criteria and independent verification.
- Clause 3.10.6.9 says a harness allows replacement of components, subject to authorisation from the manufacturer.
Australia and New Zealand
| Code | Wording |
|---|---|
| SafeWork NSW, Tree works code of practice, March 2026, section 4.1 | Modifications to climbing equipment should only be made by the manufacturer or according to a specification provided by the manufacturer or a competent person. |
| SafeWork NSW, section 8.3 | Lowering equipment should be proprietary manufactured and load rated, and only rated equipment designed for lifting, lowering or pulling loads should be used. Lowering devices should only be modified or repaired by the manufacturer. |
| WorkSafe New Zealand, approved code of practice, November 2012, section 3.2 | Climbing equipment shall not be marked for identification, for example by engraving, or altered in any way that undermines its structural integrity. Harnesses shall not be altered in a manner that would compromise their integrity. |
| WorkSafe New Zealand, section 3.2 | In the checks on ancillary equipment, the code says: do not modify or repair equipment. |
A maker notice
One maker's technical notice for a rope ascender shows how a maker words it. Its icon legend lists modifications and repairs as prohibited outside the maker's own facilities, except replacement parts.
The notice's three-year guarantee excludes modifications or alterations among its listed exclusions. Uses for which the product is not designed are excluded too.
The notice states the product must not be pushed beyond its limits or used for any purpose other than those in the maker's instructions.
Where the sources differ
The ICoP and the SafeWork NSW code allow work by the maker, or by a competent person with its consent or to its specification. The maker notice bars modifications and repairs outside its own facilities, except replacement parts. The WorkSafe New Zealand wording is flatter: do not modify. The codes also differ in scope, from all equipment in the ICoP to lowering devices only in section 8.3 of the NSW code.
The codes speak of alteration, modification and repair of a maker's product. They do not define home-made gear. The NSW code is the one that asks for proprietary, load-rated lowering equipment. A closer page on the lowering side is home-built and unrated lowering gear.
Sources
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 19, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 19, 2026
- WorkSafe New Zealand, Safety and health in arboriculture approved code of practice, November 2012, read October 19, 2026
- Petzl, Technical notice BASIC, document B0004700G (170625), read October 19, 2026