ArbNation Join free

Machine-assisted takedown: how HSE and SafeWork NSW describe excavators in felling

HSE names machine-assisted takedown of large edge trees and hung-up trees as the site of many incidents. SafeWork NSW's 2026 tree works code sets out how excavators and bulldozers may assist a fell.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and regulators are described here as published. It is not training and does not teach the work. Some wording is adapted from Health and Safety Executive pages published under the Open Government Licence v3.0, and some from the SafeWork NSW tree works code of practice, licensed under Creative Commons Attribution 4.0.

HSE on machine-assisted takedown

The Health and Safety Executive (HSE) opens its page on machine-assisted takedown with a record of harm. Many incidents have occurred where operators use machines to assist in the takedown of large edge trees and of hung-up or leaning trees.

HSE then sets one requirement: every operator must receive appropriate training. It lists four subjects:

  • how to operate the machine
  • how to do the tasks required
  • the use of personal protective equipment (PPE)
  • how to keep the machine in good working order

HSE on excavators in tree work

The HSE page on excavators covers safe working practices for tracked 360 degree excavators and walking excavators in forestry and other tree work. When the machine is used for lifting, the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) apply. HSE gives cable crane operations and lowering culvert pipes as examples where the excavator may need a current certificate of thorough examination.

HSE ties the machine to the risk assessment. Before work starts, the assessment identifies whether the machine suits the site and the task. HSE lists these items for the assessment:

  • site conditions and terrain
  • the weather
  • operation and parking of the machine
  • maintenance and transport
  • preparation to work
  • emergency procedures

The operator is at risk of falling during on-site maintenance and refuelling, so HSE calls for suitable means of access and safe working positions. Operators must be trained to operate the machine and do the tasks required. HSE adds that a relevant NPTC FMOC qualification should be obtained for the type of excavator work being done.

SafeWork NSW on powered plant for felling and pushing

SafeWork NSW approved its Tree works code of practice under section 274 of the Work Health and Safety Act 2011 (NSW). The code commenced on 27 March 2026 and replaces the 1998 Amenity Tree Industry Code of practice. Section 9.3 is titled "Use of powered plant for felling / pushing trees".

Section 9.3 says powered mobile plant fitted with rollover protective structures (ROPS) and falling-object protective structures (FOPS), with excavators and bulldozers as its examples, may assist tree felling where appropriate. The section splits into checks before felling and points during felling.

Section 9.3 of the SafeWork NSW Tree works code of practice, March 2026
StageWhat the section lists
Before fellingInspection of the tree for major structural defects. Exclusion and drop zones established and maintained. Confirmation that the plant has enough height, weight and stability to control the tree.
During fellingPlant positioned for "effective leverage", ideally in line with the intended fall. Plant in place before the tree feller approaches the tree. Only enough pressure to prevent the tree sitting back while cuts are made.
CommunicationClear communication between the tree feller and the plant operator, and an agreed safe escape zone.
Plant operatorRemains in the cab until the tree is safely committed to fall.
Ground workersAll stay outside the drop zone once cutting begins.

For restricted spaces of less than two tree lengths, the section says additional measures may be needed. Its examples are near-side root removal, adjusted scarf and back cut techniques, and ropes to help control the direction of fall.

The code's section on controlled directional felling covers pulling and pushing. It states that pushing operations must use suitable mobile plant only. Where vehicles or mobile plant serve as anchors for ropes or cables, they are kept outside the drop zone.

Reach of the two sources

The two sources cover different ground. The HSE pages deal with training, the risk assessment and the lifting regulations for the machine. Section 9.3 of the NSW code deals with positioning, communication and the plant operator's place in the cab.

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. SafeWork NSW, Tree works code of practice, March 2026, is licensed under Creative Commons Attribution 4.0 (CC BY 4.0), copyright State of New South Wales (SafeWork NSW).

Sources