ArbNation Join free

Mulchers and mulching heads: ISO 11839 guards, Forest Service and WorkSafeBC

ISO 11839:2021 tests thrown object guards for cutting and grinding attachments. A US Forest Service paper counts mulcher teeth among thrown-object hazards, and WorkSafeBC Part 26 sets hazard areas around logging equipment.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here.

ISO 11839:2021

ISO 11839:2021 is titled Machinery for forestry, Thrown object guard, Test method and performance criteria. It is edition 2, published February 19, 2021, from ISO/TC 23/SC 15, and it revises the 2010 edition. The 2010 edition, since withdrawn, was titled Glazing and panel materials used in operator enclosures for protection against thrown sawteeth.

The abstract sets out a laboratory test method and performance requirements for thrown object guards (TOG). It applies to mobile and self-propelled machinery used in forestry and related operations, including the machines defined in ISO 6814. The TOG is meant to give reasonable protection to the operator on the host machine from two things: powered rotating cutting or grinding elements, and residual matter thrown by an attachment.

Two limits sit in the abstract. The test results depend on mass, velocity and the profile of the cutting or grinding element. A guard that meets the standard is therefore specific to each cutting or grinding attachment and host machine model. The document does not address saw chain shot, which ISO 21876 covers.

AFNOR lists the French edition as NF ISO 11839, January 2022, 19 pages, status current, ICS 65.060.80. Its catalogue page prints the older glazing title next to the 2021 scope text.

Forest Service research on thrown objects

The paper is Thrown object hazards in forest operations, by Rummer and Klepac of the Southern Research Station, presented at the 2011 National Symposium on Agriculture, Forestry, and Fishing Health and Safety in Boise. Its abstract reports anecdotal accounts of thrown objects that document a risk of injury and fatality to operators of forestry cutting machines.

The full paper describes mulching machines as machines that grind through understory vegetation and small trees, reducing all the material to smaller pieces. It gives cutting speeds for the three cutter families it covers.

Cutting deviceSpeed in the paper
Chainsaw-type cuttersChain up to 40 m/s
Large disc saws on feller-bunchersTip speed above 100 m/s
Grinding or shredding cutters on mulching machinesTip speeds of about 50 m/s

The paper sorts thrown-object incidents into three kinds of hazard for equipment operators: chainshot, sawteeth or cutters from disc saws and mulching machines, and foreign objects displaced by a cutting tool. It says sawteeth and mulcher teeth carry energy similar to a shotgun slug, but they are heavier and slower. Stopping a thrown object takes a solid material, either a steel panel or polycarbonate glazing.

The paper also describes the 2010 ISO 11839 test. It simulates the actual hazard with two test levels: a lower energy object that may suit smaller machines, and a high energy object that stands for the upper limit of current cutting designs. Polycarbonate must be tested cold and warm.

WorkSafeBC Part 26

Part 26 of the British Columbia OHS Regulation covers forestry operations. Its text does not name mulchers. Three sections on logging equipment, enacted by B.C. Reg. 20/2008 and effective May 1, 2008, set out hazard-area duties.

  • Section 26.14.1: a hazard area created by operating logging equipment must be identified and communicated to every worker close to the equipment and the area. A worker must not enter or cross it on foot until the equipment operator gives permission in a clear and unmistakable manner.
  • Section 26.14.2: a safe work area must be designated for workers on foot near operating logging equipment, and its boundaries communicated. No equipment may enter it until the operator has permission from every worker in the area or from their supervisor, and those workers have taken a safe position.
  • Section 26.14.3: effective traffic control must be in place where road vehicles in a forestry operation drive through a hazard area or a safe work area.

Section 26.13.4 deals with saw chain shot only. It applies to mobile equipment with a chain saw, used in mechanical falling or log processing, built on or after May 1, 2019. Cab windows must be shielded, or be at least 32 mm of polycarbonate, or meet the level 1 ballistics tests of ANSI/UL 752.

Sources