Recovering bogged forest and tree machines: what HSE publishes on debogging
HSE's debogging page sets out a site and incident risk assessment, the operator's actions on losing traction and the safety coordinator's options. WorkSafe NZ and SafeWork NSW cover winch-assist brakes and ground-condition risk in their forestry codes.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. The core text is the HSE web page on recovery of bogged down forestry machines, which covers forestry and other tree work. WorkSafe New Zealand and SafeWork NSW publish forestry codes with related duties.
HSE on the hazard
HSE opens with the hazard. When traction is lost, the operator should stop the machine as soon as possible. The deeper the machine sits, the greater the forces needed to recover it and the greater the risk of injury, equipment failure or damage.
Risk assessment before work
HSE calls for a site-specific and incident-specific risk assessment before work begins, to identify hazards on site and the controls they need. The assessment covers four things.
- Standing or damaged trees.
- Ground conditions.
- Machine conditions.
- Manual handling of the debogging equipment.
HSE adds that travelling routes are planned to avoid, or thatch, wet or rutted areas. If the route is in doubt, an alternative route is used where one exists, and work stops if the site becomes too wet. All operators are trained in operating the equipment and in the tasks required.
When traction is lost
HSE lists what the operator does once a machine is bogged.
- Stop all drive to the tracks or wheels.
- Make the machine safe.
- Dismount safely, for example by climbing off on the high side when on a slope, if practicable.
- Assess the situation.
- Advise the site safety coordinator and arrange any assistance needed.
The safety coordinator then considers anything that may help recovery, for example partial or full unloading. Where ponded water may damage the engine or its components, the coordinator considers emergency drainage, if that is safe to do.
Winch-assist rules in the WorkSafe NZ code
WorkSafe NZ's approved code of practice for forestry operations has a Part E on mobile plant and harvesting. Part E covers mechanised harvesting including winch-assisted harvesting, manual felling including machine-assisted felling, and cable logging. Its mobile plant section does not mention bogged machines. It includes the braking and winch rules below.
- Every machine has a braking mechanism that can hold itself and its load on any slope where it operates.
- Where winch-assist is used, the winch braking system can hold the machine if traction or stability is lost.
- Mobile plant on steep slopes has an emergency stop that immediately brakes the machine or winch.
- Plant used as a winch-assist anchor has a monitoring system that detects machine movement.
The same section calls for a specific hazard management plan where slope, terrain or ground conditions risk instability of mobile plant.
Ground conditions in the SafeWork NSW code
The SafeWork NSW code of practice Safety in forest harvesting, December 2025 edition, names machine stability under different ground conditions as a common hazard. Its risk assessment of ground conditions lists these factors:
- working uphill, downhill or across a slope;
- length and degree of slope;
- size and arrangement of trees or logs compared with the machine's weight;
- broken ground, soil types, stumps, holes and rock;
- weather that affects safe working.
The code also has a section on cable and winch assisted logging, with a hazard table that includes slopes, ground foundation, anchor points and clearance distances. It does not discuss bogged machines.
Sources
- HSE, Recovery of bogged down forestry machines (debogging), page dated August 26, 2026, read October 19, 2026
- WorkSafe New Zealand, Forestry, with the Safe practice for forestry and harvesting operations approved code of practice, read October 19, 2026
- WorkSafe New Zealand, Safe practice for forestry and harvesting operations, Part E, 18.0 Introduction to Part E, read October 19, 2026
- WorkSafe New Zealand, Safe practice for forestry and harvesting operations, Part E, 19.0 Mobile plant, read October 19, 2026
- SafeWork NSW, Safety in forest harvesting code of practice, December 2025, read October 19, 2026