Reduction cuts versus heading cuts: how pruning standards word the difference
The European Tree Pruning Standard calls a head cut and a reduction cut the same thing, pruning to a lateral, and recommends a lateral of at least one third of the cut diameter. Cutting with no such lateral is a stub cut.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
Pruning cuts are described below as the European standard, the British Standards Institution and the ISA publish them. It is not training and does not teach the work.
The European Tree Pruning Standard (2021, first edition, from the TeST working group, Technical Standards in Treework) names its cut types in section 3.3. BS 3998:2010, Tree work: recommendations, is listed by the British Standards Institution as general recommendations for tree work, with no cut wording on the public listing. The ISA's Arborist News for February 2010 summarises a research review of pruning.
Pruning to a lateral
Section 3.3.3 of the European standard puts two names on one cut: pruning to a lateral, "head cut, reduction cut". It defines the cut as removal of the main axis, the leader, of a branch or limb, leaving a living side branch to carry the rest.
- The standard recommends a vigorous lateral with a diameter of at least one third of the diameter of the pruning wound.
- The lateral should form a logical extension of the parent stem. The cut should not change the direction of the branch axis much or leave a weak joint such as a dog leg.
- The cut is placed at a slant, outside the bark ridge, in the area of the remaining lateral.
Stub cutting
Section 3.3.4 defines stub cutting, also called an internodal cut, as removal of a branch that leaves a stub with no lateral leader of enough size, one third of the stem diameter. Section 3.3.3 adds that pruning to a lateral of too small a diameter, or to epicormic shoots, counts as stub cutting.
Crown reduction in the standard
| Intervention | What the standard says |
|---|---|
| Lateral crown reduction (3.4.2) | Reduces the side or lower parts of the crown. It does not touch the top and does not change tree height. Cuts should be as small as possible. Regrowth is a reaction to the work, so the reduction will often be repeated. |
| Upper crown reduction (3.4.3) | Reduces the top of the crown. It often irreversibly changes the crown architecture and the physiology of the whole tree. An inspection within 3 to 5 years is set out, and combining it with removal of lower branches is called inadvisable. |
| Topping (3.4.4.8) | Topping of semi-mature or mature trees with no fixed artificial form and no planned repeat pruning is called bad tree work to be avoided at all times. It leads to large wounds, dysfunction and decay, and topped trees are mutilated trees. |
For outgrown secondary crowns, section 3.4.5.7 says reductions below the previous cutting or breakage level should be avoided.
Heading back and regrowth in the research summary
Clark and Matheny, writing for the ISA, describe utility pruning as a case where research changed practice. Trees under energised conductors had long been headed back to a shaved, smooth crown. The problem they name is the rapid regrowth that follows. Directional pruning replaced that round-over trimming and uses both removal cuts and reduction cuts, so new growth is directed to branches pointing away from the conductors.
On reduction itself, the authors write that shortening a limb cuts its mass and its lever arm, and that arborists assume failure potential falls too. They find no evidence of how much weight or length must go to reach a set gain in stability. In their words, research has shown how to make a reduction cut but not how applying it over a whole tree helps. Their summary of the review is that crown cleaning, thinning and branch reduction have no sound scientific basis for an effect on tree health or stability, and they add that this is no reason to abandon current methods.
Sources
- TeST working group, European Tree Pruning Standard, 1st edition, June 2021, sections 3.3 to 3.4, read October 16, 2026
- British Standards Institution, BS 3998:2010 Tree work. Recommendations, listing and scope, read October 16, 2026
- James R. Clark and Nelda Matheny, ISA Arborist News, February 2010, research summary on pruning, read October 16, 2026