Rope access versus tree work: how EN 813, EN 12841 and the tree codes differ in scope
Rope access standards cover sit harnesses and rope adjustment devices. Tree codes borrow some of them and add their own. BSI scope notes, the UK industry code, the New South Wales code and the UIAA list show where each applies.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The tree documents are the Industry Code of Practice for Arboriculture, Tree Work at Height (Edition 2, May 2020), and the SafeWork NSW Tree works code of practice (March 2026). BSI records give the rope access scopes.
Standards with rope access in the title or scope
| Standard | Scope as recorded |
|---|---|
| BS EN 813:2008 | Sit harnesses for restraint, work positioning and rope access systems, where a low point of attachment is required. Sit harnesses are not suitable for fall arrest. BSI records it as published September 30, 2008 and withdrawn March 27, 2024 |
| BS EN 12841:2024 | Personal fall protection equipment, rope access systems, rope adjustment devices. BSI records it as published March 31, 2024 and current, under review |
| AS/NZS ISO 22846.1:2020 | Personal equipment for protection against falls, rope access systems, fundamental principles for a system of work. Named in the NSW tree code |
| BS EN 12277 | Mountaineering equipment, harnesses, safety requirements and test methods. Listed in the UK industry code |
Standards in the tree codes
The UK industry code lists its work equipment standards in Part 6. The list includes BS EN 813 and BS EN 12841 beside the mountaineering standards BS EN 567 (rope clamps), BS EN 892 (dynamic mountaineering ropes), BS EN 12277 (harnesses) and BS EN 1891 (low stretch kernmantel ropes). Its bibliography lists the IRATA International Code of Practice for Industrial Rope Access, 2014.
The NSW code points climbers to three standards: AS/NZS 1891.1:2020 on harnesses, AS/NZS 1891.4:2025 on selection, use and maintenance, and AS/NZS ISO 22846.1:2020 on rope access systems. It lists industrial rope access systems among the methods of access to a tree, with temporary work platforms and climbing.
How the NSW code separates the two
Section 7.2 of the NSW code covers trees on natural cliff faces, retaining walls and steep ground. It says safety measures such as industrial rope access systems should be adopted there, and that standard tree climbing systems and techniques should not be used. It defines industrial rope access as a harness-based fibre rope suspension system that incorporates a working rope and a safety rope. The code adds that the techniques differ from standard harness-based tree climbing and suit non-tree structures or terrains better.
The same code says harnesses used for the rope access methods of tree climbing are not suitable for the crane access method. Its crane section points to AS/NZS 1891.1:2020 for the harness.
The New Zealand best practice guide
The New Zealand Arboricultural Association guide, Edition 3.1 of 2022, defines moving rope technique as a climbing system for access and work positioning. It notes that the technique is commonly used in the rope access industry, which references two separate lines, an access line and a safety or back up line. Arborists double the same line instead, and the guide calls this DdRT.
UIAA standards
The UIAA began making safety standards in 1960 with ropes and lists standards for over 25 types of safety equipment. It works with CEN, the European Committee for Standardization, and in some cases asks for additional tests, so UIAA and CEN standards may differ slightly. The UIAA list includes standards for ropes (101), harnesses (105), low stretch ropes (107), rope clamps (126) and braking devices (129).
Sources
- BSI Knowledge, BS EN 813:2008 Personal fall protection equipment. Sit harnesses, read October 16, 2026
- BSI Knowledge, BS EN 12841:2024 Personal fall protection equipment. Rope access systems. Rope adjustment devices, read October 16, 2026
- Arboricultural Association and partners, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 16, 2026
- UIAA, Safety Standards, list of UIAA standards, read October 16, 2026
- New Zealand Arboricultural Association, Best Practice Guide for Safety Requirements in New Zealand Arboricultural Operations, Edition 3.1, 2022, read October 16, 2026