Safety boots for tree work: EN ISO 20345, EN ISO 17249, ASTM F2413 and CSA Z195
OSHA names ASTM F2413 and ANSI Z41, HSE names EN ISO 20345 and EN ISO 17249 for chainsaw work, and WorkSafeBC names CSA Z195, ANSI Z41 and EN 345 or 346. Each regulator lists its own footwear standards.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. It lists the footwear standards named by OSHA 29 CFR 1910.136, HSE's two tree work PPE pages and the WorkSafeBC OHS Regulation, with the scope of the two European standards as catalogued by the Estonian standards body.
Standards named by each regulator
| Standard | Named by | For what |
|---|---|---|
| ASTM F2412-2005 and F2413-2005 | OSHA, 1910.136(b)(1)(i) | Protective footwear: test methods and performance requirements |
| ANSI Z41-1999 and Z41-1991 | OSHA, 1910.136(b)(1)(ii) and (iii); WorkSafeBC 8.22(3) names the 1991 edition | Protective footwear |
| BS EN ISO 20345 | HSE, aerial tree work PPE page | Protective boots with good grip and guarding at the front vamp and instep |
| BS EN ISO 17249 | HSE, chainsaw PPE page | Protective boots for chainsaw use on the ground and off the ground |
| CAN/CSA-Z195-M92 | WorkSafeBC 8.22(3)(a) | Footwear with toe, metatarsal, puncture-resistant or dielectric protection |
| BS EN 345:1993 and BS EN 346:1993 | WorkSafeBC 8.22(3)(c) and (d) | Same list of protections as above |
United States
OSHA 1910.136(a) requires protective footwear where there is a danger of foot injury from falling or rolling objects, from objects piercing the sole, or from an electrical hazard that remains after other protective measures. Paragraph (b)(1) says the footwear must comply with ASTM F-2412-2005 and F-2413-2005, or with ANSI Z41-1999, or with ANSI Z41-1991. Under (b)(2), footwear the employer shows to be at least as effective as one of those is deemed to comply. The paragraph names no chainsaw-cut class.
Great Britain
HSE's page on PPE for aerial tree work lists protective boots with good grip and protective guarding at the front vamp and instep, complying with BS EN ISO 20345. HSE's chainsaw PPE page lists BS EN ISO 17249 for the same boot description, for work on the ground and off the ground. It also lists BS EN 381-9 for occasional users on even ground with little risk of tripping or snagging, worn with steel toe-capped safety boots.
The Estonian standards catalogue gives the scope of each European standard.
- EN ISO 20345:2022, valid from 1 April 2022: basic and additional requirements for safety footwear for general purpose use, covering mechanical risks, slip resistance, thermal risks and ergonomic behaviour.
- EN ISO 17249:2013, valid from 9 December 2013: requirements for safety footwear with resistance to chain saw cutting.
British Columbia
Section 8.22(1) of the OHS Regulation requires footwear of a design, construction and material appropriate to the protection needed, allowing the worker to work safely. Subsection (2) lists twelve factors to consider, among them slipping, tripping, uneven terrain, ankle support, crushing and puncture hazards. Where toe or metatarsal protection, puncture-resistant soles or dielectric protection are required, subsection (3) says the footwear must meet CAN/CSA-Z195-M92, ANSI Z41-1991, BS EN 345:1993 or BS EN 346:1993.
Section 8.23 requires non-slip footwear on slippery surfaces and caulked or equally effective footwear for walking on logs, poles, pilings or other round timbers. Chain saw leg protection is a separate rule, section 8.21.
Sources
- US Department of Labor, OSHA, 29 CFR 1910.136 Foot protection, read October 16, 2026
- HSE, Personal Protective Equipment (PPE) for aerial tree work, read October 16, 2026
- HSE, Chainsaw personal protective equipment (PPE), read October 16, 2026
- WorkSafeBC, OHS Regulation Part 8, Personal Protective Clothing and Equipment, read October 16, 2026
- Estonian Centre for Standardisation and Accreditation, catalogue entry EVS-EN ISO 20345:2022, read October 16, 2026
- Estonian Centre for Standardisation and Accreditation, catalogue entry EVS-EN ISO 17249:2013, read October 16, 2026