Slabs from urban trees: what FPL and extension say about species, thickness and drying
Nebraska Forest Service names live edge slabs, most often 2 inches thick, as one of three urban lumber products. It puts air-drying of a 2-inch slab at up to 2 years.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
This page draws on the named extension services and the Forest Products Laboratory as they published. It is not training and does not teach the work. The sources are Nebraska Forest Service on urban lumber, Purdue Extension publication FNR-93, Oregon State Extension publication EM 8612 and chapter 13 of the Wood Handbook (FPL-GTR-282, March 2021). None of them is a slab guide on its own, so the figures below sit under each source's own conditions.
Why city logs differ
Nebraska Forest Service describes community trees as open grown. They tend to produce larger canopies and shorter logs, especially short trunks, than forest trees. That affects which lumber products they can supply.
Purdue Extension notes that many shade trees are open grown and fast growing. They are often not the most desirable lumber species and may contain metal. Lawn mowers, weed whips and improper pruning can leave wounds at the base or on the trunk. That damage usually brings localized decay and discoloration.
The three urban lumber products
Nebraska Forest Service sorts urban lumber into industrial lumber, rough lumber and live edge lumber and slabs.
| Product | Description |
|---|---|
| Industrial lumber | Large dimension cants, resawn into smaller pieces for pallets. Made with four cuts. Sold green |
| Rough lumber | Usually cut to 1 to 2 inch thicknesses and sold with or without drying or planing. Drying is necessary before use in finished products |
| Live edge lumber and slabs | Most commonly sold in 2 inch thick slabs, with smaller dimensions too |
In the Lincoln urban wood study, Nebraska Forest Service staff milled 25 city ash logs on a hydraulic band sawmill. The report says the lumber was of higher quality than expected. Many surface defects visible on the logs were gone once the logs were milled into slabs or rough lumber. A skid steer was needed to move logs, and three people were needed at all times: one sawing and two moving logs and lumber.
Species
Purdue Extension ranks hardwoods by desirability for urban lumber:
- Cherry, oak, sugar maple and walnut: some of the most valuable and desirable.
- Ash, basswood, silver maple and red maple: intermediate.
- Beech, hickory and yellow poplar: of the least value.
- Cottonwood and sycamore: usually end up as pallet stock or blocking.
The same publication gives log size. Portable mills can cut logs as small as 6 or 8 inches in diameter, but most logs should be about 10 inches or larger on the small end inside the bark. Larger logs and logs from the butt of the tree usually give lumber with fewer defects. More knots and bumps on a log mean lower quality lumber.
Purdue also covers time between felling and sawing. Logs are best processed soon after cutting. In warm months, the longer logs lie, the greater the chance of stain, decay and insect attack. These problems do not develop in cold winter months. In oak, walnut and cherry the heartwood has some natural decay and insect resistance, while the sapwood is destroyed in about a year or less. For other species, a year of exposure seriously damages the whole log.
Thickness and drying time
Thickness drives drying time. For Nebraska Forest Service, a 2 inch thick slab takes up to 2 years to air-dry. Oregon State Extension reports that 2 inch lumber can take three to four times as long as 1 inch lumber of the same species to air-dry to a given moisture content. Its general range for air-drying to a target is several months to almost a year, and wood stored outdoors under cover dries to about 12 to 14 percent in western Oregon and 8 to 10 percent in eastern Oregon.
The Wood Handbook gives extremes for 1 inch lumber air-dried to 20 to 25 percent moisture content. Low density species such as pine, spruce, red alder and soft maple take 15 to 30 days in favourable places and seasons. Slow-drying species such as oak and birch take 200 to 300 days in northern locations at unfavourable times of year. Drying is very slow in cold winter months, and hot, dry winds may increase degrade and volume losses from severe surface checking and end splitting.
The Handbook lists the usual end-use moisture contents. Hardwood lumber for furniture, flooring, cabinets and millwork is usually dried to 6 to 8 percent.
End coating and stacking
For species prone to checking, such as oak, Oregon State Extension calls for an end coating as soon as possible, preferably in the woods before the logs are hauled. End coatings are usually wax-based, and they lose effectiveness once the lumber starts to dry. In the Wood Handbook, end coating may alleviate end checking. For oaks, Oregon State puts the maximum safe moisture loss at about 1 to 2 percent a day.
Both Oregon State and Purdue describe stickered stacks. Oregon State reports 1 inch thick stickers as common, with spacing of about 18 to 24 inches for lumber of almost any size and 12 inches for hardwoods such as elm. Its text bars stacking over vegetation-covered ground and notes that direct sun speeds drying. Purdue describes stickers about 3/4 inch by 1 1/2 inches placed on 18 inch to 2 foot centres, a cover of tin sheets rather than plastic, and a level stack at least 6 inches off the ground.
Kiln drying
Nebraska Forest Service lists kiln drying of slabs as an option, with the kiln operator needing to be proficient in drying to hold the slabs' value. It names dehumidification kilns and solar kilns as relatively low investment, with operation and drying times that vary by season. Traditional and vacuum kilns dry much more quickly. In the Wood Handbook, air-drying to 20 to 25 percent before the kiln saves energy, because kiln drying uses the most energy of all wood production processes.
Sources
- Nebraska Forest Service, Urban Lumber Production, read October 19, 2026
- Purdue University Cooperative Extension Service, FNR-93 Use of Urban and Development Site Trees for Lumber (Cassens and McKenzie, 2002), read October 19, 2026
- Oregon State University Extension Service, EM 8612 Air- and Shed-drying Lumber (Reeb and Brown, reprinted October 2007), read October 19, 2026
- US Forest Service Forest Products Laboratory, Wood Handbook (FPL-GTR-282, 2021), chapter 13 drying, PDF, read October 19, 2026