Spark arrestor screens on chainsaws: the USFS guide, the 0.023-inch limit and Oregon's power saw rule
The US Forest Service tests chainsaw spark arresters to a 0.023-inch particle limit and lists qualified saws in its Spark Arrester Guide. Oregon's fire-season power saw rule points to that list.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here.
What the Forest Service tests
The Spark Arrester Guide, Volume 2, April 2007, from the Forest Service Fire Management programme, covers multiposition small engines. It defines those as hand-held internal combustion engines that work in more than one position, and it names chain saws first. Testing follows SAE Recommended Practice J335.
The guide defines a spark arrester as a device that traps or pulverizes exhaust carbon to below 0.023 inch in diameter. Exhaust particles are mostly carbon and can leave at more than 3,000 °F. The guide says a particle larger than 0.023 inch at 1,200 °F can ignite cellulose material on contact.
Screens and mounting systems are checked for openings no larger than 0.023 inch. Exposed surfaces may not exceed 550 °F and exhaust gases may not exceed 475 °F, measured with the saw working under optimal load.
The 2003 Forest Service Tech Tip on general-purpose arresters adds a collection test: the arrester must collect at least 80 percent of the particles. It also says the Service evaluates every arrester submitted for approval, under Specification 5100-1 and Society of Automotive Engineers standards. Qualified units appear in the next edition of the guide.
The qualified list and the whole saw
In the guide, the arrester is not just the screen. The spark arrester system includes the engine, internal and external parts, bumper spikes, wrap-around handlebar, chain brake, covers and muffler. Whatever the qualified list names for a model is the minimum. A larger spike than the one listed is permitted, and optional parts are limited to those listed.
| Point | What the guide prints |
|---|---|
| Marking | The model number and the maker's name or trademark identify the unit. The words "Qualified" or "Approved" are not required and do not show that a unit is qualified |
| Not on the list | The absence of an arrester from the lists indicates it may not have been qualified |
| Modification | Any modification or damage to the system as tested voids the qualification. Examples named: removed screen, changed exhaust outlets, smaller bumper spikes, removed chain brakes or hand guards, a wrong handlebar |
| Inspection items | Screen in good condition with a proper fit in its holder and no opening over 0.023 inch; all required parts present; correct handlebar, bumper spikes and chain brake; no changes to exhaust or engine |
| Window screen | Window screen or soft screen is not an approved spark arrester screen |
| Gauge | A 0.024-inch wire gauge is the check for screen size |
Saws made before 1978
The guide has a separate rule for chain saws manufactured before June 30, 1978. Their exhaust gases must pass through a screen with no opening larger than 0.023 inch. The screen must resist heat and corrosion and provide at least 100 hours of service life.
A general-purpose stainless steel screen of 0.023 inch is allowed only on those older saws, and only where the saw is not listed in the guide. The guide says to find a saw's age by asking the operator or calling the dealer with the serial number.
Oregon: the power saw rule
Oregon Administrative Rule 629-043-0036, issued under ORS 477.640, applies to anyone operating a power saw during fire season inside a forest protection district or within one-eighth of a mile of one. The rule requires the saw to carry a spark arrester and other fire prevention equipment listed in the latest edition of the Spark Arrester Guide Volume 2. A saw modified from the tested and listed configuration is prohibited during fire season.
The rule also lists tools that must be immediately available when a saw is running. One is a gallon of water or a pressurized fire suppressant container of at least eight ounces. The other is a round pointed shovel with a face at least 8 inches wide and a handle at least 26 inches long. The motor is stopped for fueling and moved at least 20 feet from the fueling place before starting. Spark arresters, screens and other equipment are kept ready for immediate use. The forester may reduce or waive any requirement by written order.
Federal land fire orders
Title 36 of the Code of Federal Regulations, section 261.52, sits in Subpart B, Prohibitions in Areas Designated by Order. It lists acts prohibited when provided by an order. The list includes building a fire, smoking, welding and, at item (g), operating an internal combustion engine.
The list and the maker
The qualified list in the guide names saws by maker and model, with the parts each model needs to keep its qualification. The Tech Tip adds that the Spark Arrester Guide is the only authoritative industry source on qualified arresters, and that a model not found in it is not qualified.
Sources
- USDA Forest Service, Spark Arrester Guide Volume 2, Multiposition Small Engine, 5100 Fire Management, April 2007 (Idaho Department of Lands copy), read October 16, 2026
- USDA Forest Service San Dimas Technology and Development Center, Tech Tip 0351 1306, General-Purpose Spark Arresters, May 2003, PDF, read October 16, 2026
- USDA Forest Service, Tech Tip 0351 1306, General-Purpose Spark Arrestors, web edition, read October 16, 2026
- Oregon Department of Forestry, OAR 629-043-0036 Power Saws (via Oregon Administrative Rules text), read October 16, 2026
- 36 CFR 261.52 Fire, Electronic Code of Federal Regulations, 89 FR 92816, read October 16, 2026