Timber cruising terms: basal area, board feet per acre and point sampling defined
Basal area is the cross-sectional area of a trunk at breast height, summed per acre. Point sampling counts trees through a prism of a set basal area factor, and each counted tree stands for that factor in square feet per acre.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
Terms defined
| Term | Definition as published | Source |
|---|---|---|
| Basal area (BA) | The cross-sectional area of a tree stem at the point where diameter is measured, bark included, in square feet. For timber species the point is diameter at breast height. Summed over a stand, it is usually given as square feet of basal area per acre. | USFS Forest Inventory and Analysis (FIA) standard terminology |
| Diameter at breast height (DBH) | The diameter of a tree measured 4.5 feet above the ground. | University of Arkansas Extension FSA5036 |
| Trees per acre (TPA) | The number of tree stems in one acre of forest. | University of Arkansas Extension FSA5036 |
| Board-foot volume | The wood in an unfinished board 1.0 foot wide, 1.0 foot long and 1.0 inch thick. It is computed for the sawlog portion of a sawtimber-size tree, from a 1-foot stump to a minimum top of 7.0 inches diameter outside bark for softwoods or 9.0 inches for hardwoods. | USFS FIA standard terminology |
| Net board-foot volume | Gross board-foot volume in the sawlog portion, less deductions for cull. Cull deductions cover rotten or missing material and form defect. | USFS FIA standard terminology |
| Variable radius plot | A point-based plot design where a tree is "in" according to its size against a basal area factor on a prism or angle gauge and its distance from the centre point. | USFS FIA standard terminology |
| Basal area factor (BAF) | The basal area per acre that each tallied tree stands for. The MSU bulletin gives 10 square feet per acre for an angle of 1.736 degrees. | MSU Extension E-1757; Clemson Extension |
| Point sampling | A variable radius method, also called prism or Bitterlich sampling. Trees are chosen by size rather than frequency, so larger trees are more likely to be tallied. | Clemson Extension; MSU Extension E-1757 |
| Limiting distance | The plot radius for one tree: the plot radius factor multiplied by that tree's DBH. | Clemson Extension |
| Tree expansion factor | The factor that scales a sample tree to a per-unit basis such as trees per acre. The factor varies with the plot design. | USFS FIA standard terminology |
| MBF | Thousand board feet. | University of Arkansas Extension FSA5036 |
Point sampling and the basal area factor
The MSU Extension bulletin E-1757, issued May 1984, explains point sampling in one picture. At an angle of 1.736 degrees, a 10-inch tree within 27.5 feet of the sample point appears larger than the projected angle and is selected. That is a circular plot of 0.05454 acre. A 20-inch tree is picked up out to 55 feet, a sampling area of 0.21816 acre, so it has twice the radius and four times the area.
Each selected tree stands for the same basal area per acre whatever its size: 10 square feet at that angle. The bulletin gives the estimate as the average number of sample trees per point multiplied by the basal area factor. It calls prisms of factor 10.0 common in Michigan.
Clemson Extension describes the basal area factor as the prism's rating, with common values of 5, 10 and 20. A higher factor tallies fewer trees, and each one stands for more basal area. It gives a plot radius factor of 2.75 feet per inch of DBH for a 10 BAF prism, so a 10-inch tree has a limiting distance of 27.5 feet. For a 1-inch tree the radius is 3.90 feet at 5 BAF, 2.75 feet at 10 BAF and 2.25 feet at 20 BAF.
How many trees per point
The two extension publications put the tally count in similar ranges. MSU Extension says to choose the prism that gives 5 to 10 trees per point, with the 10-factor prism for stands up to 100 square feet of basal area per acre and the 20-factor above that. Clemson Extension suggests a factor that yields five to twelve tally trees per point. For the number of points, Clemson gives at least 30 in natural stands or 20 in even-aged plantations. MSU Extension gives 3 to 7 points for stand reconnaissance and 10 to 100 for a compartment examination, depending on stand size.
Basal area arithmetic
University of Arkansas Extension gives the fixed-plot formula as tree basal area in square feet equal to 0.005454 times DBH squared, multiplied by the expansion factor. For a 1/10 acre plot repeated four times, the expansion factor is 10 divided by 4, or 2.5. For variable plots it multiplies the tally by the factor and divides by the number of plots: 80 trees times a 10 BAF gives 800, and 800 over 5 plots is 160 square feet of basal area per acre. The same publication uses the DBH classes pulpwood 6 inches and up, chip-n-saw 8 to 12 inches and sawtimber 12 inches and up.
Board feet per acre
None of the four publications prints a definition of the phrase board feet per acre. The USFS glossary defines the board-foot volume of a tree, and Arkansas Extension says an estimate needs DBH and tree height, then a species-specific volume table. Clemson Extension reports volume in cubic feet per acre, with a worked total of 1,471.7 cubic feet, and does not report board feet. MSU Extension E-1757 works a preliminary sawtimber estimate in thousand board feet per acre: Scribner MBF per acre equals 0.6 times the average number of sawlogs per point, so 12.4 sawlogs gives 7.4 MBF per acre.
The USFS glossary says all FIA work units compute board feet by the International 1/4-inch rule, and that some units (RMRS and PNWRS) also compute them by the Scribner rule. Arkansas Extension prints these log rules:
| Rule | Formula printed | Description printed |
|---|---|---|
| Doyle | (D-4)² x (L/16) | D is diameter inside the bark and L is length in feet. It works well for larger trees and loses accuracy the smaller the trees. |
| Scribner | (D-4)² x L / 16 | D is diameter inside the bark at the small end of the log. A more conservative estimate that does not account for taper, so it underestimates the volume of longer logs. |
| International | Log constant times D², less log constant times D, less a length term | Called the most accurate of the three and the most time-consuming. Printed for 4, 8, 12, 16 and 20 foot lengths, for example 0.796 x D² - 1.375 x D - 1.230 for 16 feet. |
Arkansas Extension gives Doyle and Scribner the same expression and no separate Scribner constant.
Volume and weight conversions
Arkansas Extension converts between volume and weight. A standard cord is 128 cubic feet with bark. A cord of pine is 75 cubic feet of solid wood and a cord of mixed hardwood is 80. One cubic metre is 35.315 cubic feet. For sawtimber it lists tons per thousand board feet: for pine, 7.0 by Scribner, 8.0 by Doyle and 5.5 by International; for hardwood, 8.0, 9.0 and 6.5 by the same three rules. For pulpwood it lists 5,350 pounds per cord of pine and 5,800 pounds per cord of hardwood.
Sources
- USDA Forest Service, Forest Inventory and Analysis national program, standard terminology glossary, November 2, 2022, read October 21, 2026
- Michigan State University Extension, E-1757 Aids to Professional Forestry Practice, Robert Marty, May 1984, read October 21, 2026
- Clemson Cooperative Extension, How to Conduct a Timber Cruise, read October 21, 2026
- University of Arkansas System Division of Agriculture, FSA5036 How Much Timber Do I Have: A Landowner's Guide to Evaluating Basal Area and Volume, May 2025, read October 21, 2026